Rimage 8200N Guia De Instalacion página 2

3
Set up your printer (continued)
g.
Install the retransfer ribbon.
i.
Grasp the handle to slide the retransfer ribbon
carrier out of the printer.
Note: The retransfer ribbon carrier can not be
removed from the printer.
ii.
Slide the retransfer ribbon under the
retransfer ribbon carrier.
Note: The ribbon winds under the supply roll,
as shown.
iii. Snap the supply roll and take-up roll onto the
carrier.
iv.
Tighten the retransfer ribbon by turning the takeup roller counterclockwise.
v.
Slide the retransfer ribbon carrier into the printer.
vi.
Close latches 1, 2, and 3, as indicated by the
arrows.
vii. Close the printer side cover.
h.
Place the printer on the Producer IV so that the
plastic printer feet slide into the slots on the printer
plate.
i. Connect the cables.
i.
Connect the printer cable from the Producer IV
to the printer.
ii.
Connect the USB cable to the printer.
iii.
Connect the power cord from the Producer IV to the printer.
4
Connect the cables and cords
a. Make sure that the main power switch on the back of the Producer IV is in the 'off'
position.
b.
Connect the power cord to the system
then connect the power cord from the
Producer IV to a power outlet.
Important!
•
Do not power on the Producer IV
until you are instructed to do so.
•
The outlet must be an earth-
grounded outlet.
c. Connect the network cable to the
Power Cord
embedded control center then connect
the cable to your network.
d. Connect the USB cable from the printer
to one of the USB ports on the back of
the system.
Note: Rimage recommends you connect the USB cable from the printer to a USB 2
port.
e. Connect a monitor, mouse, and keyboard for local control.
Note: You may need to attach a monitor, mouse, and keyboard to make the initial
network connection. A Remote Desktop Connection can then be made. Once the
connection is established, the monitor, mouse, and keyboard can be removed.
2002546_A
5
Load discs in the system
Retransfer Ribbon
Carrier
The default bin configuration is:
•
•
•
Refer to the Rimage Producer IV User Guide for information on changing bin
configuration.
Supply Roll Take-up Roll
Note: If you have a Blu-ray Disc
configuration information.
6
Power on the system
a.
Printer Cable
USB Cable
b.
Power
Cord
7
Log on
Note: Rimage recommends that your Network Administrator use these
instructions as a guide to complete the configuration and software installation.
•
USB 2 Ports
Network Cable
•
Load CDs in Bin 1.
Load DVDs in Bin 2.
Load DVD-DL in Bin 3.
TM system, refer to your user guide for bin
PC Power
Press the main power switch
Button
at the back of the Producer IV
to the 'on' position.
Press the power button on
the front of the Producer IV to
power on the embedded PC.
Note: After the system powers on, the system begins the initialization
process. Initialization may take up to 5 minutes. During the initialization
process the lift arm moves to each recorder and the printer. When the lift
arm assembly stops moving, initialization is complete and your system is
ready to process jobs.
If this system is connected to a network, access is made through Microsoft
Remote Desktop Connection running on a separate PC. See the Rimage
Advanced Setup (Networking) Guide for information on accessing Remote
Desktop Connection and WebRSM.
Note: If you are accessing the system remotely, you must wait to log on until
the system initialization completes. This may take several minutes. The
Carousel, Retransfer and Ribbon statuses display repeatedly on the
autoloader operator panel when the system is finished initializing.
Important! If there is more than one Rimage system on the network, you
must change the computer name. Refer to the Rimage Advanced Setup
(Networking) Guide for instructions.
If you connected a monitor, keyboard, and mouse, log on to the Producer IV
with the following information:
Windows 7/Windows Server 2008 R2:
User name: User
Password: password1! (case sensitive)
Copyright © 2012 Rimage
8
Test and verify
Use QuickDisc to run a 3-disc test job to verify that the system is operating correctly.
Note: You can now use Rimage WebRSM to adjust the system settings.
9
Register the Rimage system
Register your Rimage system to receive parts and labor covered for 1 year and priority
phone support.
Product registration and warranty activation is available at
www.rimage.com/support/warranty-registration.
10
Learn more
•
These documents are available on the Rimage Producer IV User Guide disc that
shipped with your autoloader:
Rimage Producer IV User Guide
ƒ
Rimage Advanced Setup (Networking) Guide
ƒ
Diagnostic Test Instructions
ƒ
Access these documents by placing the User Guide disc in the disc drive of a PC.
Note: If the User Guide menu does not display automatically, browse to the
Home.htm file on the software disc.
• For information about submitting orders to the Producer IV across a network,
or to view the latest information on remote accessing, refer to the Rimage
Advanced Setup (Networking) Guide.
•
For information about operating and maintaining the Producer IV, refer to the
Rimage Producer IV User Guide.
• For additional support and product information, go to
www.rimage.com/support.
Page 2