Samoa RM-12CLX Serie Guía De Servicio Técnico Y Recambio página 10

EN
TENSOR PIECE REPLACEMENT
6. Probably the power spring will stop pulling the hose before completely
coiled the 6 meters (20') previously uncoiled. This is a good sign
about we are making properly the procedure. In any case, be careful
not letting the hose end to introduce inside the reel casing.
7. Avoid the hose end to introduce inside the reel casing, and make
sure the spring has lost all its load and it remains relaxed. The spool
must not tend to turn. If still the spring has remaining load, repeat
the procedure since step 1.
8. Now it is necessary to take away the casing side, for doing this,
proceed to take apart the bolts (1) (fig. 20).
9. Take apart the two bolts (2) (fig. 20) located in the roller outlet side.
10. Disassemble the base (4) (fig. 20) by loosening the bolts (5) (fig. 20).
11. Loosen the bolts (3) (fig. 20) which join both casing sides. Now you
can take apart the casing side (6) (fig. 20) been able to access the
Tensor piece (7 & 8) (fig. 20).
DISPOSAL AND RECYCLING INFORMATION
• This product has been developed and manufactured with high
quality materials and components which mostly can be recycled
and/or reused, such as metals: (brass, aluminum, and steel, mainly)
and also thermoplastic polymers: (PP and HIPS, mainly).
This product must be disposed of separately from ordinary household
wastes at its end of life. Please dispose of this product at your local
collection point or recycling centre. Do this to make sure that the
product is recycled in an environmental friendly way, and help to
protect the environment in which we all live.
• This product has been designed to minimize as far as possible its
environmental impact. For that propose, different strategies has
been implemented in addition to using recyclable and not dangerous
materials. Some of these strategies are shown as follows:
• The quantity of components has been reduced, and also the variety
of different raw materials needed to manufacture the product.
The overall dimensions and the weight have been reduced to
minimize the environment impact during transport and storage.
DIMENSIONS AND SPARE PARTS LIST
See pages: 20, 21 and 22.
10
850 840 R. 09/19
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
12. Replace the tensor piece (7) (fig. 20) and its inner metal sheet (8)
(fig. 20) for a new ones. Make sure to assemble the inner metal sheet
inside the plastic tensor piece, before placing the assembly on the
spring fixation (9) (fig. 20).
13. Assemble again all the components in reverse order, by placing the
unassembled casing side (6) (fig. 20) and fixing it to the other casing
side by tightening the bolts (3) (fig. 20).
14. Assemble the base again (4 & 5) (fig. 20), and the roller outlet bolts
(2) (fig. 20).
15. Finally, apply load to de power spring following the steps shown at
point 6 to 10 on chapter "hose installation".
As far as possible, already existing parts have been used to reduce
the quantity of new components to be created.
The different components have been tested for maximum toughness
and durability.
These hose reels are powered by an autonomous spring. Not batteries
are used, and no electrical consumption or other energy source is
needed. This product has no electrical or electronic components.
By using hose reels at the working place, the hoses working life is
increased. Also the fluids handling becomes cleaner and safer,
avoiding spills and improving the healthy and security at the
working place.
• All this measures, among other ones, are oriented to achieve a more
environment-friendly product, because they contribute to reduce
resources needed throughout the product life cycle, such as:
manufacturing, assembly, maintenance, transport, and storage; and
also the generated waste is reduced when the product reach its
lifetime end.