Samoa RM-12CLX Serie Guía De Servicio Técnico Y Recambio página 7

ROLLER OUTLET REPLACEMENT
1. Uncoil a short leght of the hose, only to avoid the hose stopper to
contact with the roller outlet. Make sure to latch the spool. For
higher security, use a tool which avoid the spool to turn freely. If not,
it is recommended to block de spool by introducing an Allen key 7
mm between faces (1) (fig. 8) inside the brass hexagon (2) (fig. 8),
through the Tensor piece (3) (fig. 8).
CAUTION: Beware not to free the latch because the spool can
!
get loose and start turning freely, which could cause injure.
2. Loosen the bolts (1) (fig. 14) and take away the roller outlet assembly
(2) (fig. 14) which can be disassembled in a single piece. The roller
outlet assembly can be disassembled into pieces for cleaning. Also
you can replace it by a new roller outlet assembly.
3. Once the roller outlet assembly has been cleaned or replaced by a
new one, it is necessary to assemble all its components. For doing
this, first of all you should place the long rollers (1) (fig. 15) in its
position over the roller supports (2) (fig. 15), and go through this
assembly with the long axles (3) (fig. 15). This way, you should have
two equal components pre-assembled (4) (fig. 15).
4. Now take the short axles (2) (fig. 16) to go through the short rollers
(1) (fig. 16) and use these components to join both preassembled
components made in the previous step (4) (fig. 16). For doing this,
manually exert pressure to introduce the short axles pins, in the long
axles holes (3) (fig. 16).
5. Take the assembled roller outlet and put it in place over the hose
reel, and fix it using the bolts (1) (fig. 14).
4
SPOOL & POWER SPRING REPLACEMENT
This reel model uses a power spring to coil the hose. This power spring
no requires maintenance, and with a reasonable use, it is unusual a
power spring failure. Because of this, probably it would be not necessary
you to replace the power spring during the hose reel service life.
The power spring is a component subjected to high loads, even when it
is relaxed, so it is recommended not no manipulate or replace the power
spring to avoid risk of serious injuries.
In any case, if it is necessary to replace the power spring, it is available a
spool kit, which contains the power spring confined inside. This way, it
would not be necessary to manipulate the power spring directly.
SAMOA Industrial, S.A. · Pol. Ind. Porceyo, I-14 · Camino del Fontán, 831 · 33392 - Gijón - Spain · Tel.: +34 985 381 488 · www.samoaindustrial.com
2
3
1
Fig. 15
6. Holding the hose, unlatch the spool removing all the tools used, and
gently let the hose to coil.
Fig. 14
1
4
2
1
3
TO REPLACE THE HOSE REEL SPOOL, FOLLOW THE NEXT STEPS:
1. First of all is necessary to remove the power spring tension. To do so,
with all the hose coiled and the hose stopper contacting with the
roller outlet, introduce a square key (1) (fig. 9) in the Tensor piece
(2) (fig. 9), and loosen the bolts (3) (fig. 9). Do not turn the tool (1)
(fig. 9) until all the bolts have been taken away, because the stress
could damage the Tensor piece (3) (fig. 10).
WARNING: Extreme caution while applying tension adjustments
!
to the power spring, because it has strong force. Grab firmly the
key and the hose reel, using heavy leather gloves. If the spool
starts to turn freely, it could cause injuries.
EN
1
2
Fig. 16
R. 09/19 850 840 7