SKIL MASTERS F0151450 Serie Manual Original página 11

- continue to cut along the cutting line in a clockwise
direction with the accessory base resting fl at on the
workpiece
- cut slowly for optimal control (fast cutting will cause
excessive heat and may shorten the service life of
the bit)
- after completing the cut, switch off the tool and
carefully remove it from the workpiece
! always test out first on a piece of scrap material
• Cutting soft wall tiles @
! insert tile bit S
- create a starting-point for plunge cutting by slowly
making a groove on the tile's surface at a 45° angle
- start rotating the tool at a 45° angle, while keeping
the point of the cutting bit fi rmly positioned within the
groove
- continue rotating the tool until the cutting bit has
completely plunged through the wall tile
- move the tool to a 90° angle and guide it up and
down along the desired cutting line (the up and down
movement prolongs the service life of the cutting bit)
• Holding and guiding the tool #
! while working, always hold the tool at the grey-
coloured grip area(s)
- hold tool fi rmly with both hands, so you will have full
control of the tool at all times
- keep ventilation slots R 2 uncovered
- do not apply too much presssure on the tool
(excessive pressure will cause excessive heat and
may shorten the service life of the accessory)
APPLICATION ADVICE
• For making circular cut-outs use circular guide T $
• When cutting a hole in a vertical surface, start and end
your cut at the top, so that the scrap part will not drop
onto the rotating bit
MAINTENANCE / SERVICE
• Always keep tool and cord clean (especially the
ventilation slots R 2)
! do not attempt to clean ventilation slots by
inserting pointed objects through openings
! disconnect the plug before cleaning
• Always clean depth adjustment accessory H 2 and
dust suction accessory M 2 after use
• If the tool should fail despite the care taken in
manufacturing and testing procedures, repair should be
carried out by an after-sales service centre for SKIL
power tools
- send the tool undismantled together with proof of
purchase to your dealer or the nearest SKIL service
station (addresses as well as the service diagram of
the tool are listed on www.skilmasters.com)
ENVIRONMENT
• Do not dispose of electric tools, accessories and
packaging together with household waste material
(only for EU countries)
- in observance of European Directive 2002/96/EC on
waste of electric and electronic equipment and its
implementation in accordance with national law,
electric tools that have reached the end of their life
must be collected separately and returned to an
environmentally compatible recycling facility
- symbol % will remind you of this when the need for
disposing occurs
CE DECLARATION OF CONFORMITY
• We declare under our sole responsibility that this
product is in conformity with the following standards or
standardized documents: EN 60 745, EN 55 014, in
accordance with the provisions of the directives
2006/95/EC, 2004/108/EC, 98/37/EC (until Dec. 28,
2009), 2006/42/EC (from Dec. 29, 2009 on)
• Technical file at: SKIL Europe BV (PT-SEU/PJE),
4825 BD Breda, NL
09 SKIL Europe BV
NOISE/VIBRATION
• Measured in accordance with EN 60 745 the sound
pressure level of this tool is 88 dB(A) and the sound
power level 99 dB(A) (standard deviation: 3 dB), and the
vibration 3.0 m/s² (hand-arm method; uncertainty
K = 1.5 m/s²)
• The vibration emission level has been measured in
accordance with a standardised test given in
EN 60 745; it may be used to compare one tool with
another and as a preliminary assessment of exposure to
vibration when using the tool for the applications
mentioned
- using the tool for different applications, or with
different or poorly maintainted accessories, may
signifi cantly increase the exposure level
- the times when the tool is switched off or when it is
running but not actually doing the job, may
signifi cantly reduce the exposure level
! protect yourself against the effects of vibration by
maintaining the tool and its accessories, keeping
your hands warm, and organizing your work
patterns
F
Perceuse
INTRODUCTION
• Cet outil a été conçu pour couper le gypse, le bois, le
plexiglass, le plastique et les carreaux muraux mous
• Lisez et conservez ce manuel d'instructions 3
SPECIFICATIONS TECHNIQUES 1
11
A. v.d. Kloot
1450