ROBBE Nine Eagles SOLO PRO 287 RTF GHz Manual Del Usuario página 13

Replacement Parts List, SOLO PRO 287 RTF
Order No. Description
NE251501 Main rotor blades
NE251502 Swashplate guide
NE251503 Canopy mount
NE251504 Motor mount
NE251505 Toothed belt pulley
NE251506 Canopy
NE251507 Landing gear
NE251508 Chassis frame
NE251509 Toothed belt
NE251510 Horizontal stabiliser
NE251511 Tail rotor brace
NE251512 Tail rotor pushrod bracket
NE251513 Belt tensioner bracket
NE251514 Tail rotor blades
NE251515 Tail rotor blade holder
NE251516 Tail rotor housing
NE251517 Vertical stabiliser
NE251518 Main rotor blade holder
NE251519 Rubber grommets set
NE251520 Tail rotor servo mount
NE251521 Main rotor head
NE251522 Swashplate
NE251523 Pushrod set
NE251524 Main gear set
NE251525 Tail rotor linkage
NE251526 Tail rotor control arm
NE251527 Tail rotor pushrod
NE251528 Belt tensioner
NE251529 Freewheel bearing
NE251530 Blade pivot shaft
NE251531 Ballrace, 2 x 5 x 2.5
13
Order No. Description
NE251532 Main rotor shaft collet
NE251533 Ball-end bolt
NE251534 Ball-end bolt, servo output arm
NE251535 PB screw, 1.7 x 4
NE251536 PB screw, 1.7 x 7
NE251537 Tail boom
NE251538 Tail rotor hub
NE251539 Ballrace, 6 x 8 x 2 ZZ
NE251540 Tail rotor shaft
NE251541 Allen-head screw, M3 x 3
NE251542 Allen-head screw, M2 x 2
NE251543 Allen-head screw, M2 x 10
NE251544 Allen-head screw, M2 x 12
NE251545 Self-locking nut, M2
NE251546 PB screw, 1.6 x 10
NE251547 Ballrace, 4 x 7 x 2
NE251548 Ballrace support
NE251549 Allen-head screw, M2 x 7
NE251550 Washer, 2.1 Ø x 6
NE251551 Countersunk screw, M2 x 4
NE251552 Thrust bearing, 2 x 7 x 3.5
NE251553 Washer, 5.5 Ø x 7
NE251554 Plain bush
NE251555 Washer, 2.0 x 3.8
NE251556 Washer, 2.6 x 4.5
NE251557 PB screw, 1.4 x 5
NE251558 Main rotor shaft
NE251559 PB screw,1.4 x 2.5
NE251560 Allen-head screw, M2.5 x 6
NE251561 Allen-head screw, M2 x 8
NE251562 Washer, 2.6 x 6
SOLO PRO 287 RTF 2,4 GHz
Order No. Description
NE251563 BL motor
NE251564 LiPo battery, 11.1 V / 850 mAh, 30C
NE251565 Receiver
NE251566 BL controller, 20 A
NE251567 Mains PSU, 230 V (not shown)
NE480090 NES9G tail rotor servo
NE480064 NES8G DIG servo
NE200113 Battery charger
When replacing components it is very important
to use the correct type of cross-point screwdriver
and to tighten the screws with great care.