Install Produce Preserver (On Some Models) - JENN-AIR JS48NXFXDE Manual De Uso Y Cuidado

Tabla de contenido

Publicidad

Idiomas disponibles

Idiomas disponibles

■ Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.
Style 2 (Non-Dispenser Models)
IMPORTANT: After connecting the refrigerator to a water source
or replacing the water filter, fill and discard two full containers of
ice to prepare the water filter for use, before using the ice.
Do not use with water that is microbiologically unsafe or of
unknown quality without adequate disinfection before or
after the system.
NOTE: If your model has a base grille filter system, make sure
the base grille filter is properly installed and the cap is in the
horizontal position.
1. Turn on the ice maker. Lower the wire shutoff arm as shown.
Please refer to "Ice Maker and Storage Bin" for further
instructions on the operation of your ice maker.
NOTES:
■ Allow 24 hours to produce the first batch of ice.
■ Allow 3 days to completely fill ice container.
■ Depending on your model, you may want to select the
maximum ice feature to increase the production of ice.
Install Produce Preserver
(on some models)
The produce preserver absorbs ethylene to slow the ripening
process of many produce items. As a result, certain produce
items will stay fresh longer.
Ethylene production and sensitivity varies depending on the type
of fruit or vegetable. To preserve freshness, it is best to separate
produce with sensitivity to ethylene from fruits that produce
moderate to high amounts of ethylene.
Sensitivity to
Apples
Asparagus
Berries
Broccoli
Cantaloupe
Carrots
Citrus Fruit
Grapes
Lettuce
Pears
Spinach
Ethylene
Ethylene
Production
High
Very High
Medium
Very Low
Low
Low
High
Very Low
Medium
High
Low
Very Low
Medium
Very Low
Low
Very Low
High
Very Low
High
Very High
High
Very Low
Installing the Produce Preserver (on some models)
CAUTION: IRRITANT
MAY IRRITATE EYES AND SKIN. DANGEROUS FUMES
FORM WHEN MIXED WITH OTHER PRODUCTS.
Do not mix with cleaning products containing ammonia,
bleach or acids. Do not get in eyes, on skin or clothing. Do
not breathe dust. Keep out of reach of children.
FIRST AID TREATMENT: Contains potassium
permanganate. If swallowed, call a Poison Control Center or
doctor immediately. Do not induce vomiting. If in eyes, rinse
with water for 15 minutes. If on skin, rinse with water.
1. Wash the interior of a crisper drawer with a solution of mild
dish soap and warm water, and dry thoroughly.
2. Find the package containing the Produce Preserver inside the
refrigerator, and install the Produce Preserver into the crisper
drawer according to the instructions provided in the package.
Installing the Status Indicator (on some models)
The Produce Preserver comes with a status indicator, which
should be activated and installed at the same time the pouch
is installed.
1. Place the indicator face-down on a firm, flat surface.
2. Apply pressure to the bubble on the back of the indicator
until the bubble pops to activate the indicator.
3. Slide open the cap on the Produce Preserver housing.
4. Place the indicator in the top of the housing facing outward.
5. Slide the cap closed, and check that the indicator is visible
through the rectangular hole in the cap.
NOTE: The cap will not easily close if the indicator's rear
bubble has not been popped.
Replacing the Produce Preserver
The disposable packets should be replaced every 6 months or
when the status indicator changes completely from white to red.
To order replacements, see "Accessories" in the User Instructions
or User Guide.
1. Remove the used packets from the produce preserver
housing.
2. Remove the used status indicator.
3. Install the replacement packets and status indicator using
the instructions included in the package.
5

Publicidad

Tabla de contenido

Solución de problemas

loading

Este manual también es adecuado para:

Js42nxfxdeJs48ppdudeJs42ppdude

Tabla de contenido