Troubleshooting - Black and Decker GW3031BP Manual Del Usuario

Fitting and removing the concentrator
sweeping motion; the debris/leaves will be sucked up the
tube, shredded and thrown into the back pack collection
switch off the appliance and unplug from the mains power
supply.
Unclip the the catch (3a) on the back pack collection bag
empty its contents.
Warning! Never remove the collection bag without first turning
off and unplugging the appliance.
Note: If the suction decreases and the bag is not full, the
vacuum tube is probably clogged with debris. Turn off and
unplug the vacuum and clear the tube before continuing.
Position the rake (18) above the mount (19) on the bottom
of the lower vacuum tube (8).
(19) until it clicks into place.
To remove, lift the rake release (20) and slide the rake
(18) off the mount (19).
Align the 2 markers (16) on bottom of the upper blow tube
(4) and the 2 markers (17) on the bottom of the lower blow
tube (5).
tube (5) until they click into place.
Warning! Do not separate the tubes once assembled.
the lower blow tube (5). Secure the concentrator by cliping
the tab (31) onto the clip (32)
To remove, lift the clip (32) and slide the concentrator (30)
off the bottom of the lower blow tube(5).
Warning! Grip the product firmly when switching on.
To switch the appliance on, turn the variable speed control
To switch the appliance off, turn the variable speed
control (1) anti-clockwise to the off position.
Attach the fan cover (22) to the powerhead (11) by
locating the assembly as indicated by the arrow, then pivot
about this point and press the vac release button (9) until
the catch (23) is fully engaged.
bag (fig. G).
As the bag fills, the power of the suction will decrease,
u
u
(fig H).
Unfold the opening of the back pack collection pack (fig I).
u
Open the back pack collection pack (fig J) and proceed to
u
Fitting and removing the rake (fig. E) (GW3031BP
unit only)
u
Push down and slide the rake (18) firmly onto the mount
u
u
Blow tube assembly (fig. K)
u
Push the upper blow tube (4) firmly into the lower blow
u
Slide the concentrator (30) firmly onto the bottom end of
u
u
Switching on and off (fig. F)
u
(1) clockwise to the required setting.
u
Blow mode (fig. K, L)
u
Removing the blow tube and fan cover

Troubleshooting

Maintenance
(Original instructions)
Align the assembled blow tube with the power head (11).
Push the assembled blow tube onto the vacuum outlet
(25) until the lock engages tightly with the blow tube.
Warning! Never operate in Blow mode without the blow tube
Hold the blow tube approximately 180 mm above the
ground, switch on the appliance and using a sweeping
motion from side to side, advance slowly keeping the
Once you have blown the debris/leaves into a pile, you
can convert to vacuum mode to collect the debris.
Remove the fan cover (22) from the bottom of the power
head by inserting a screwdriver/Allen key in the slot on
the end of the fan cover (located on the back of the power
head) to actuate the internal release, and remove the fan
Problem
Your BLACK+DECKER appliance has been designed
to operate over a long period of time with a minimum of
maintenance.
Continuous satisfactory operation depends upon proper
appliance care and regular cleaning.
Keep the appliance clean and dry.
Check the connection to the power supply
Check the fuse in the plug, if blown, replace (UK
only).
Check that the blow/vacuum tube assembly is
Failure to operate
If the fuse continues to blow - immediately
disconnect from the mains power supply and consult
your local BLACK+DECKER authorised
repair agent.
Switch off - disconnect from the mains power
supply, debris should fall clear of the tube.
Remove and empty the collection bag.
Check that both the inlet and exit ports on the
Poor vacuum/high vacuum tube are clear.
pitched whine
Remove any debris from the fan area
If poor vacuuming continues - immediately
disconnect from the mains power supply and
consult your local BLACK+DECKER authorised
repair agent
Switch off - disconnect from the mains power
supply and remove the collection bag.
Remove the vacuum tube and inspect the
fan.
Poor shredding
Clean any debris from the fan blades.
If the fan is cracked or damaged, do not use
- consult your local BLACK+DECKER
authorised repair agent.
u
u
and fan cover firmly in place.
u
accumulated debris/leaves in front of you (fig. L).
u
u
cover (figure B).
correctly fitted to the powerhead.
u
ENGLISH
Possible solution
9