Stanley FATMAX FMC627 Manual Del Usuario página 7

Ocultar thumbs Ver también para FATMAX FMC627:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 35
Drilling/screwdriving
LED work light
State of charge indicator
Hints for optimum use
Drilling
Screwdriving
For drilling in masonry, align the hammer icon on the
mode select collar (5) with the marking (16).
Slide the speed selector (6) towards the front of the tool
(2nd gear).
For drilling in steel and for screwdriving applications, slide
the speed selector (6) towards the rear of the tool (1st
gear).
For drilling in materials other than steel, slide the speed
selector (6) towards the front of the tool (2nd gear).
Select forward or reverse rotation using the forward/
reverse slider (2).
To switch the tool on, press the switch (1). The tool speed
depends on how far you press the switch.
To switch the tool off, release the switch.
The LED work light (9) is activated automatically when the
trigger is depressed. The LED work light will illuminate when
the trigger is partially depressed, before the unit begins
running.
used to display the current level of charge in the battery during
use.
Press the state of charge indicator button (11).
Always apply a light pressure in a straight line with the drill
bit.
Just before the drill tip breaks through the other side of the
workpiece, decrease pressure on the tool.
Use a block of wood to back up workpieces that may
splinter.
Use spade bits when drilling large diameter holes in wood.
Use HSS drill bits when drilling in metal.
Use masonry bits when drilling in soft masonry.
Use a lubricant when drilling metals other than cast iron
and brass.
Make an indentation using a centre punch at the centre of
the hole to be drilled in order to improve accuracy.
Always use the correct type and size of screwdriver bit.
amount of washing liquid or soap as a lubricant.
Drilling in masonry (fig. D & E)
u
u
Speed selector (fig. E)
u
u
u
u
u
The tool is fitted with a state of charge indicator. This can be
u
u
u
u
u
u
u
u
u
u
If screws are difficult to tighten, try applying a small
u
Z
Maintenance
Protecting the environment
Technical data
(Original instructions)
Always hold the tool and screwdriver bit in a straight line
with the screw.
Your Stanley Fat Max tool has been designed to operate over
a long period of time with a minimum of maintenance.
Continuous satisfactory operation depends upon proper tool
care and regular cleaning.
Your charger does not require any maintenance apart from
regular cleaning.
Warning! Before performing any maintenance on the tool,
remove the battery from the tool. Unplug the charger before
cleaning it.
Regularly clean the ventilation slots in your tool and
charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth.
Do not use any abrasive or solvent-based cleaner.
Regularly open the chuck and tap it to remove any dust
from the interior.
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled reducing the demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com.
Voltage
V
No-load speed
Min
Nm
Chuck capacity
mm
Max Drilling capacity
Steel/wood/
mm
masonry
Charger
Input Voltage
Output Voltage
Current
DC
u
u
u
u
u
Max. torque
ENGLISH
FMC627 (H1)
18
0-450/0-1800
57
13
13/38/13
905998**
906086**
typ. 1
typ. 1
V
230
230
V
18
18
A
1
2
-1
AC
DC
7

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

616684000000

Tabla de contenido