Denver MRP-161 Manual Del Usuario página 27

The LCD display (2) will display the first & second digit of " 00 " is flashing. Press skip up
3.
set the correct hour. Press " Mem/Clk-adj " button (14) to store the correct hour.
The third & fourth digit of " 00 " is flashing, press the skip up
4.
Then press " Mem/Clk-adj " button (14) to store the correct minute.
Listening to radio
Manual tuning
1. Tune on the unit by press power On/Standby button (7)
2. Press Function button (10) to select " Tuner " mode.
3. Tune to the required station by pressing the skip up
4. Adjust volume up/down button (14) to the desired volume level.
Auto tuning
Press Function button (10) to select " Tuner " mode.
1.
2. Press and hold the skip up/down button (25,12) for 1-2 seconds and then release.
3. The unit will start seeking automatically and stop until a radio station is reached.
4. Repeat step 2 until the desired radio station is being reached.
5. Adjust volume up/down button (3) to the desired volume level.
Preset stations
You can store up to 10 radio stations in the memory (10 FM).
1. Set to tuner mode.
Turn to the desired radio station by " manual" or " auto " tuning method.
2.
Press " Mem/Clk-adj " button (14) to enable program function & " MEM " icon and preset station nr will flash on LCD display (2)
3.
Press " Pre-up
4. or Pre-dn
Press " Mem/Clk-adj " button (14) again to confirm the setting.
5.
6. Repeat step 2 to 5 to store other stations.
Now you can select the presets stations in order by pressing the "Pre–up
7.

The pre-set memories will be cancelled completely if dis-connecting the main power supply. You are recommended to
switch the system into standby mode for convenience usage.

There are 10 seconds for program state, after 10 sec. This state would resume to normal tuner mode automatically.

You can overwrite a present station by storing another frequency in its place.
FM & FM-stereo reception
 Press the " St/Mono " button (8) repeatedly, the FM programs are receiving in mono and stereo mode repeatedly. In particular
when stereo signals are weak. It is preferable to receive the program in mono.
 If stereo signal is being received, the stereo indicator "
receiving.
Hints for best reception:-
- FM : the receiver has a build-in FM wire antenna (34) hanging at the back of the unit. This wire should be totally unraveled and
extended for the best reception.
Phono
noted:
- Remove the stylus protector.
- Be sure that the tone arm is being detached from the tone arm rest before operating and re-secured again afterwards.
Press Function button (10) to select " Phono " mode.
1. Set the speed selector (30) to the proper position depending on the type of record to be played.
2. Place the record on the platter (use the spindle adaptor (29) if required).
3. Lift the tone arm from the pick up holder (31) and slowly move it to the record side. The platter will
start to rotate.
4. Place the tone arm to the desired position of the record.
5. Adjust the Volume up/down button (3) to the desired level.
6. At the end of record, the platter will automatically stop rotating. Lift the tone arm from the record and
return it to the rest position (31).
7. To stop intermediate, lift up the tone arm from the record and return it to the rest (31).
Remark : As some kind of record the auto-stop area was out of the unit setting, so it will stop before the last
track finish. In this case, select the auto-stop switch (33) to " off "position, then it will run to the end of the
record but will not stop automatically (turn off the unit by power button or switch back the auto-stop switch (33)
to " on " position to stop the platter rotate). Then put back the tone arm to the rest position (31).
Playing compact disc

Getting start
Press Function button (10) to select " CD " mode.
1.
Press " Open/Close " button (24) to open the CD tray (17).
2.
3. Place a CD with the printed side facing up inside the tray & then close the CD tray.
4. Focus search is performing, then will start the playback automatically.

Play / pause mode
or skip down
" button (26,13) to select the desired station memory for storage.
EN-2
or skip down button (25,12) to set the correct minutes.
button (25,12).
" button (26) or Pre-dn
" will appear on LCD display (2) to show FM stereo program is now
or skip down button (25,12) to
button (13).