Device Description; Using The Device; Cleaning And Maintenance; Technical Data - camry Premium CR 7905 Manual De Uso

20. Do not move the device when the inner tank is filled with water.
21. Do not place any objects on the device.
22. The device can be used only with properly working ventilation.
23. To provide additional protection, it is advisable to install a residual current device (RCD)
in the electric circuit with a rated residual current not exceeding 30mA. Ask an
electrician for this.
Before first use
1. It should be remembered that a high level of humidity may favor the development of biological organisms in the environment.
2. Do not get wet the device or wet the area around the device. If moisture appears, reduce the efficiency of the humidifying function.
3. Do not allow absorbent materials such as carpets, curtains, tablecloths to get wet.
4. Never leave water in the tank when the device is not in use.
5. During filling and cleaning, disconnect the device from the mains.
6. Clean the device and water tank before using it again.
• WARNING: When the water is not replaced and the tank is not properly cleaned every 3 days, microorganisms that may be present in
the water or in the environment where the device is used or stored may develop in the water tank and be blown out to the
surroundings. This can cause a very serious health risk.
• WARNING: Every three days, empty the water tank and top up with clean water. Before refilling, clean the tank with fresh tap water or
using detergents. Remove any scale, deposits or film that has formed on the sides of the tank and on the interior surfaces. After
washing, wipe all surfaces dry.
DESCALING
1.Perform the descaling procedure in accordance with the instructions of the descaling agent specified by the manufacturer.
2.Use descaling agents intended for this purpose.
3. Carry out the descaling procedure at least every 3 months.
4. Descaling only the water tank with the device turned off.

DEVICE DESCRIPTION

1. Air outlet opening
3. Wheels
5. Mesh filter
7. Water tank

USING THE DEVICE

A noticeable reduction in the temperature of the outlet air occurs after putting into the water tank plastic containers attached to the
product previously frozen in the freezer. It is recommended to fill the tank with cold tap water.
1. Place the unit on a dry, flat surface and connect to the power supply.
2. Pul out the water tank (7) from the back of the machine and pour in the water (Fig.B). Be careful not to exceed the maximum level.
3. In the CR7905 model, start the device by pressing the "ON" button on the control panel (8). In the CR7920 model, start the device
using the "ON / OFF" button on the control panel (8).
4. The SPEED button on the control panel allows you to change the speed of the blower unit. The following speeds can be selected:
HIGH (fast), MIDDLE (medium) and LOW (slow).
5. HUMIDIFY button lowers the temperature of the air by running the water pump. Additionally, a set of two cartridges is attached.
To use them, put them on 24 hours inside the freezer. Then add one or both of the water tank (7). To blow cool air, the device must be
filled with water. When the device is operating, periodically check the water level to see whether to add water.
6. Pressing the SWING button starts the oscillation of vertical slats that provide even distribution of cold air stream. Horizontal slats do
not move automatically, so if necessary, manually adjust them to point up or down.
7. The TIMER button allows for programming the amount of time during which the device will operate before turning itself off
automatically (if the TIMER function is not used, the device will work until it is manually turned off).
8. The MODE button allows for changing the fan mode. In addition to the normal mode, you can select "NATURE" and "SLEEP." The
NATURE mode mimics the natural wind action by changing the fan speed about every 10 seconds and changing the speed from LOW
through MIDDLE to HIGH. The SLEEP mode makes the device turn itself off after a specified period of time. If the speed is set to LOW,
the device will turn off automatically after 30 minutes. If the speed is set to MIDDLE, after 30 minutes the device will reduce the speed to
LOW and after another 30 minutes will turn off automatically. If the speed is set to HIGH, the device after 30 minutes, reduce the speed
of the MIDDLE, then after another 30 minutes, reduce the speed to LOW and after another 30 minutes, turn off automatically.
9. The ANION button is only available on the CR7920. Press the ANION button to turn on the air ionization function. Press the ANION
button again to turn off the air ionization function.
10. To turn off the device in the CR7905 model, press the "OFF" button on the control panel (8). To turn off the device in the CR7920
model, press the "ON / OFF" button on the control panel (8).

CLEANING AND MAINTENANCE

1. Clean with soft, dry cloth. Do not use chemical solvents because they can cause permanent damage or deformation of the device.
2. If the device is not used for three or more months, take the batteries out of the remote control.
3. Drain the water before storage by removing the drain plug at the bottom of the water tank. Then dry the device, mesh filter, mesh
filter's frame and housing to aviod the moisture damage.

TECHNICAL DATA:

Power source: 220-240 V ~50 Hz
Power: 60W
Power Max: 325W
Tank capacity: 8L
2. Water level indicator
4. Carrying handle (on both sides)
6. Power cord holders
8. Control panel
5