Protecting The Environment - Black and Decker XTS10EK Manual De Instrucciones

ENGLISH
Scrolling mode
In the scrolling mode, the saw blade can be rotated for
intricate and accurate sawing. It is recommended to use saw
blades suitable for scrolling in this mode.
Turn the mode selector switch (4) to position A (scrolling
N
mode). In this position there is no pendulum action.
Pendulum action mode
In the pendulum action mode, the saw blade is locked in the
forward direction to for fast straight sawing.
Turn the mode selector switch (4) to position A (scrolling
N
mode).
Rotate the saw blade into the forward direction using the
N
scroll knob (9).
Turn the mode selector switch (4) to position C (pendulum
N
action mode). In this position the scroll knob cannot be
rotated. The saw blade is locked in its position.
Variable speed control
Set the variable speed control knob (3) to the required
N
speed range. Use a high speed for wood, medium speed
for aluminium and PVC and low speed for metals other
than aluminium.
Switching on and off
To switch the tool on, press the on/off switch (1).
N
For continuous operation, press the lock-on button (2)
N
and release the on/off switch.
To switch the tool off, release the on/off switch.
N
To switch the tool off when in continuous operation, press
the on/off switch once more and release it.
How to use the SightLine™ feature (fig. G)
Use a pencil to mark the cutting line.
N
Position the jigsaw over the line (18).
N
Viewing from directly above the jigsaw the line of cut can be
easily followed. Should this view be restricted for any reason,
the indent (19) can be used as an alternate cutting guide.
Hints for optimum use
Sawing laminates
As the saw blade cuts on the upward stroke, splintering may
occur on the surface closest to the shoe plate.
Use a fine-tooth saw blade.
N
Saw from the back surface of the workpiece.
N
To minimise splintering, clamp a piece of scrap wood or
N
hardboard to both sides of the workpiece and saw
through this sandwich.
6
Scrolling
Use a saw blade suitable for scrolling wood.
N
Holding the tool with one hand, slowly move the tool to
N
follow the line of cut whilst operating the scroll knob.
Sawing metal
Be aware that sawing metal takes much more time than
N
sawing wood.
Use a saw blade suitable for sawing metal.
N
When cutting thin sheet metal, clamp a piece of scrap
N
wood to the back surface of the workpiece and cut
through this sandwich.
Spread a film of oil along the intended line of cut.
N
Accessories
The performance of your tool depends on the accessory used.
Black & Decker and Piranha accessories are engineered to
high quality standards and designed to enhance the
performance of your tool. By using these accessories you will
get the very best from your tool.
This tool is suitable both for U-shank and T-shank saw blades.
Maintenance
Your tool has been designed to operate over a long period of
time with a minimum of maintenance. Continuous satisfactory
operation depends upon proper tool care and regular cleaning.
Regularly clean the ventilation slots with a clean, dry
N
paint brush.
To clean the tool, use only mild soap and a damp cloth.
N
Never let any liquid get inside the tool and never immerse
any part of the tool into liquid.
Occasionally apply a drop of oil to the axle of the blade
N
support roller.
Mains plug replacement (U.K. & Ireland only)
If a new mains plug needs to be fitted:
Safely dispose of the old plug.
N
Connect the brown lead to the live terminal in the new
N
plug.
Connect the blue lead to the neutral terminal.
N
Warning! No connection is to be made to the earth terminal.
Follow the fitting instructions supplied with good quality
plugs. Recommended fuse: 5 A.

Protecting the environment

Separate collection. This product must not be
disposed of with normal household waste.