Descargar Imprimir esta página
Pioneer KEH-P2035 Manual De Instrucciones
Ocultar thumbs Ver también para KEH-P2035:

Publicidad

Idiomas disponibles

Idiomas disponibles

Enlaces rápidos

KEH-P2035
This product conforms to new cord colors.
Los colores de los cables de este producto se
conforman con un nuevo código de colores.
Æ...b¹b'« „öÝô« Ê«
uë lÄ "UN'« «c¼ r− M¹
Printed in Malaysia
<CZR2956-A> ES
<KSNNN/02H00000>
6
30˚
Fig. 1
Fig. 3
± qJAë
≥ qJAë
7
2
1
182
53
3
4
Fig. 2
Fig. 4
≤ qJAë
¥ qJAë
5
8
9
Fig. 5
µ qJAë
10
Fig. 6
∂ qJAë
Installation
Note:
Before finally installing the unit, connect the
wiring temporarily, making sure it is all connect-
ed up properly, and the unit and the system work
properly.
Use only the parts included with the unit to
11
ensure proper installation. The use of unautho-
rized parts can cause malfunctions.
Consult with your nearest dealer if installation
13
requires the drilling of holes or other modifica-
tions of the vehicle.
Install the unit where it does not get in the dri-
ver's way and cannot injure the passenger if there
is a sudden stop, like an emergency stop.
The semiconductor laser will be damaged if it
overheats, so don't install the unit anywhere hot
— for instance, near a heater outlet.
12
If installation angle exceeds 30° from horizontal,
the unit might not give its optimum performance.
(Fig. 1)
Fig. 7
DIN Front/Rear-mount
∑ qJAë
This unit can be properly installed either from
"Front" (conventional DIN Front-mount) or
"Rear" (DIN Rear-mount installation, utilizing
threaded screw holes at the sides of unit chassis).
For details, refer to the following illustrated
installation methods.
DIN Front-mount
Installation with the rubber bush (Fig. 2)
1. Dashboard
2. Holder
After inserting the holder into the dashboard,
then select the appropriate tabs according to the
thickness of the dashboard material and bend
them.
(Install as firmly as possible using the top and
bottom tabs. To secure, bend the tabs 90
degrees.)
3. Rubber bush
4. Screw
<ENGLISH>
Removing the Unit (Fig. 3) (Fig. 4)
5. Frame
6. Insert the release pin into the hole in the bottom
of the frame and pull out to remove the frame.
(When reattaching the frame, point the side with
a groove downwards and attach it.)
7. Insert the supplied extraction keys into the unit,
as shown in the figure, until they click into place.
Keeping the keys pressed against the sides of the
unit, pull the unit out.
DIN Rear-mount
Installation using the screw holes on
the side of the unit (Fig. 5) (Fig. 6) (Fig. 7)
1. Remove the frame.
8. Frame
9. Insert the release pin into the hole in the bottom
of the frame and pull out to remove the frame.
(When reattaching the frame, point the side with
a groove downwards and attach it.)
2. Fastening the unit to the factory
radio mounting bracket.
10. Select a position where the screw holes of the
bracket and the screw holes of the head unit
become aligned (are fitted), and tighten the
screws at 2 places on each side. Use either truss
screws (5 × 8 mm) or flush surface screws
(5 × 9 mm), depending on the shape of the screw
holes in the bracket.
11. Screw
12. Factory radio mounting bracket
13. Dashboard or Console

Publicidad

loading

Resumen de contenidos para Pioneer KEH-P2035

  • Página 1 Install the unit where it does not get in the dri- 30˚ DIN Rear-mount ver’s way and cannot injure the passenger if there KEH-P2035 is a sudden stop, like an emergency stop. • The semiconductor laser will be damaged if it Installation using the screw holes on overheats, so don’t install the unit anywhere hot...
  • Página 2: Instalación

    Instalación <ESPAÑOL> æWOÐdFëº æ VOÂd²Ã« ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ Nota: Quitado de la unidad (Fig. 3) (Fig. 4) ©¥ qJAë® ©≥ qJAë® “UN'« Ÿe½ • • Antes de finalmente instalar la unidad, conecte el 5. Marco cableado temporalmente y asegúrese de que todo 6.
  • Página 4: Connecting The Units

    Connecting the Units <ENGLISH> Note: Connection Diagram (Fig. 8) • This unit is for vehicles with a 12-volt battery • When an external power amp is being used with and negative grounding. Before installing it in a this system, be sure not to connect the blue/white 1.
  • Página 5: Conexión De Las Unidades

    Conexión de las unidades <ESPAÑOL> Nota: Diagrama de conexión (Fig. 8) • Esta unidad es para vehículos con batería de 12 • Cuando se está utilizando un amperio de potencia voltios y con conexión a tierra. Antes de instalar externa con este sistema, asegúrese de no conec- 1.
  • Página 6 æWOÐdFëº …eNł_« qO uð ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ∫WEŠöÄ ©∏ qJAë® qO u²Ã« jD Ä • • • IP-BUS ≠ (CD) • • IP-BUS • • IP-BUS • ON/OFF • • • • • • BPTL • ≠ • • •...