Place Batteries In Smartdoor; Place Battery In Smartkey; Check Operational Mode Before Installation; Check Smartdoor ™ Location Before Installation - Petsafe IRIS Electronic SmartDoor Guía Para El Uso

A. Place Batteries in the SmartDoor
1. With a Phillips screwdriver, remove the two Battery
Compartment Cover screws.
2. Remove the Battery Compartment Cover.
3. Refer to the inside of the Battery Compartment
Cover for the proper orientation of the four D-Cell
(LR20) batteries.
4. Replace the Battery Compartment Cover and re-
install the two screws.
5. When the batteries are placed in the Electronic
SmartDoor the red light will illuminate for
™
two seconds and the flap will move into the
locked position, unless the flap is already in the
locked position.
NOTE:
The door must be in the upright position for
the flap to center properly and operate correctly.
B. Place Battery in the SmartKey
1. Place the PetSafe RFA-67 battery into the bottom of
®
the SmartKey .
™
2. Using a coin, rotate one-quarter turn clockwise to
secure the PetSafe RFA-67 battery.
®
NOTE:
The SmartKey has a red light that will flash
™
when the PetSafe RFA-67 battery is low; the battery
®
should be replaced as soon as possible.
C. Check Operational Modes Before Installation
Operational Indicators
IRIS SmartDoor
™
A. Sensitivity Knob
B. IRIS Pairing Mode
Blue Indicator
C. Locked or Low Battery
Red Indicator
D. Unlocked or Learn
Mode Green Indicator
E. Automatic or Error
Mode Yellow Indicator
F. Mode-Reset
Selection Button
B C
G. Learn Mode Button
• To check if operational settings are working properly, hold down the MODE-RESET button
until each operational mode has cycled through once to allow red, green and yellow lights to
illuminate one at a time.
Operational Modes
LOCKED MODE – Does not allow entry or exit for any pet. The SmartDoor
factory in LOCKED MODE and when batteries are placed in the SmartDoor
LOCKED MODE. To set: hold the MODE-RESET button until red light illuminates and release
when selected.
UNLOCKED MODE – Allows entry and exit for all pets. To set: hold the MODE-RESET button
until the green light illuminates and release when selected.
6 1-800-732-2677
™
™
A
D E F G
ships from the
™
, it will enter
™
AUTOMATIC MODE – Allows entry and exit for a pet wearing a programmed SmartKey
To set: hold the MODE-RESET button until the yellow light illuminates and release when
selected. Five SmartKeys can be programmed to one SmartDoor
™
during AUTOMATIC MODE.
NOTE:
If at any time the red light remains illuminated, replace with a set of fresh batteries. If
that does not reset the red light, please call our Customer Care Center for additional help.
If any part of step C was unsuccessful, please call our Customer Care Center for additional help.
D. Check SmartDoor Location Before Installation
™
DO NOT REMOVE SENSITIVITY STICKER BEFORE INSTALLING THE SMARTDOOR
Prior to installation, it is recommended to check that the SmartDoor
intended location or application to guard against possible severe radio-frequency interference.
Household appliances and common electronic products should be located at least two feet (60 cm)
away from the SmartDoor 's location. Radio-frequency interference detected from other household
™
appliances or common electronic products will negatively affect the ability of the SmartDoor
receive a SmartKey signal. Typical appliances and products to consider are laptop computers,
™
wireless telephones, microwaves, televisions, garage door openers, hand-held electronic devices
(such as cell phones, game stations and remote controls).
The sticker placed over the sensitivity knob should not be removed until after installation, as the
factory default sensitivity setting is positioned at the optimal level for most installations.
It is recommended to install SmartDoor
™
Temperature Range: -5˚ F to 180˚ F (-20.5˚ C to 82˚ C). Operating Humidity Range: 0 to 99.9%.
• To check if SmartDoor 's radio-frequency technology will operate properly in desired location
™
and application, place SmartDoor directly in front of and against the door or application in the
™
upright position. After performing steps A-C, now set the SmartDoor
hold the SmartKey directly in front of the SmartDoor
™
about three seconds. Remember, the SmartKey
the SmartDoor .
™
NOTE:
If there are existing SmartKeys
™
batteries while performing step D except the SmartKey
If the SmartDoor does not unlock, move the SmartDoor
™
once more. If the SmartDoor 's location test above was unsuccessful, please call our Customer
™
Care Center for additional help.
When steps A-D are completed and all are successful, your SmartDoor

INSTALL

Installing Your SmartDoor

1 Step

Determine Pet Door Location

1A
1B
www.petsafe.net
for selective entry and exit
™
will operate properly in the
™
in a location where direct wind is not a factor. Operating
in AUTOMATIC mode and
™
. The SmartDoor flap should unlock in
™ ™
included in the kit is already programmed to
™
in the household, remove all (RFA-67)
included with the SmartDoor
™
to another location and follow steps A-D
™
is ready for installation.
™
™
1A Measure and mark your pet's shoulder
height on the door.
1B Determine location for the pet door. Draw
a vertical center line through the shoulder
height line using a level.
NOTICE
If homeowner's door or other application is
not level, the pet door must be marked level to
swing properly.
.
™
.
™
to
™
.
™
7