Transport; Storage; Care And Service; Troubleshooting Guide - Kärcher LMO 18-36 Battery Manual De Instrucciones

Mowing edges
Lawn edges, e.g. along a wall, can also be mown using
the device.
1. Push the lawnmower along the wall, close to the
wall.
Illustration M
The side inlet ensures that the grass is pulled into the
cutting zone.
Illustration N
Finishing operation
1. Release the ON/OFF switch.
Illustration O
The motor stops.
Removing the battery pack
1. Open the battery flap.
Illustration P
2. Remove the safety key.
3. Press the battery pack release.
4. Remove the battery pack.
5. Close the battery flap.
Emptying the grass catcher
The flap on the grass catcher filling lever indicator clos-
es when the grass catcher is full. Empty the grass catch-
er in this case.
1. Lift the ejection chute flap.
Illustration Q
2. Remove the grass catcher.
Take care to ensure that the motor control cable re-
mains in the cable holder when removing the grass
catcher.
3. Empty the grass catcher.

Transport

WARNING
Sharp blade
Incision injuries
Be careful when tipping or lifting the device.
Keep all parts of your body away from the cutting blade.
1. Switch the device off (see Chapter Finishing opera-
tion).
2. Ensure that the blade is no longer rotating.
3. Allow the device to cool down.
4. Remove the safety key (see Chapter Removing the
battery pack).
5. Remove the battery pack.
6. Secure the device against slipping and tipping over
when transporting in vehicles.

Storage

Clean the device before storing (see Chapter ).
1. Release the quick-release screws and fold down the
handle.
Illustration R
2. Fold over the quick-release catch and place the
handle on the device.
Illustration S
3. Place the grass catcher on the handle and the de-
vice.
Illustration T
4. Store the device in a dry, well ventilated location.
Keep away from corrosive substances such as gar-
den chemicals and defrosting salt. Do not store the
device outdoors.

Care and service

WARNING
Sharp blade
Incision injuries
Be careful when tipping or lifting the device.
Keep all parts of your body away from the cutting blade.
Cleaning the device
1. Remove the battery pack (see Chapter Removing
the battery pack).
2. Clean the exterior of the device with a soft, damp
cloth or brush each time after use.
Illustration U
Clean the blade before longer storage periods.
3. Tip the device onto the side.
Illustration V
4. Clean the blade and the underside of the device us-
ing a brush.
Illustration W
Removing blockages
WARNING
Removing blockages
Incision injuries from the sharp blade or sharp-edged
objects
Wear protective gloves when checking for blockages or
removing blockages.
1. Switch the device off and wait until the blade comes
to a standstill.
2. Remove the battery pack (see Chapter Removing
the battery pack).
3. Remove the grass catcher and check for blockages.
Remove any blockages.
4. Check the ejection shaft for blockages. Remove any
blockages.
5. Tip the device onto the side.
6. Check the underside of the device and the blade for
blockages. Be careful when removing blockages be-
cause the blade can move while doing this.
Replacing the blade
1. Remove the battery pack (see Chapter Removing
the battery pack).
2. Clean the underside of the device (see Chapter ).
3. Lock the blade and then loosen the screw.
Illustration X
4. Remove and dispose of the blade.
Illustration Y
5. Fit the new blade into the holder.
Illustration Z
6. Lock the blade and then tighten the screw.
Illustration AA

Troubleshooting guide

Malfunctions often have simple causes that you can
remedy yourself using the following overview. When in
doubt, or in the case of malfunctions not mentioned
here, please contact your authorised Customer Service.
The device switches off
The device overload protection system has triggered.
1. Release the ON/OFF switch.
2. Press the start button and the ON/OFF switch.
The battery pack overheating protection has triggered.
1. Wait until the battery pack temperature lies within
the normal range.
2. Charge the battery pack if the device cannot be
switched on.
English 21