Ryobi CLT-1423P Manual De Utilización página 21

Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 32
GB
F
D
MAINTENANCE AND REPAIR
INSTALLING A PREWOUND SPOOL
See Figure 13.
Remove the battery pack from the line trimmer.
Press in the tabs on each side of the spool cap.
Remove the spool cap and spool.
NOTE: If the spring falls off the spool housing during
this procedure, reinstall the spring before installing
the spool and spool cap.
Inspect the string head for damaged or worn parts
and clean thoroughly.
Unwind approximately 102 mm (4 in.) of the line from
the prewound spool. Hold the line and spool firmly to
keep it from unwinding then place the spool cap onto
the spool.
Holding the spool cap and spool by the bump knob,
place into the spool housing and insert cutting line
into the opening in spool housing.
NOTE: Tabs on the spool cap should be aligned with
the slots in the spool housing.
While pressing in the tabs, push down the spool cap
and spool to lock in place.
Completely assembled string head should appear as
shown. See Figure 14.
WARNING
Do not attempt to modify this unit or create or
mount
any
recommended in this manual for use with this
line trimmer. Any such alteration or modification
is misuse and could result in a hazardous
condition leading to possible serious personal
injury. Examine line trimmer frequently to assure
all parts are unbroken and securely attached.
Make sure all screws and fasteners are securely
tightened to prevent the risk of serious personal
injury.
BATTERIES
Your battery pack is equipped with Nickel- Cadmium
rechargeable batteries. Length of service from each
charging will depend on the type of work you are doing.
The batteries in this unit have been designed to provide
maximum troublefree life. However, like all batteries, they
will eventually wear out. DO NOT disassemble battery
pack and attempt to replace the batteries.
E
I
P
NL
accessory
not
specifically
S
DK
N
FIN
English
Handling of these batteries, especially when wearing
rings and jewellery, could result in serious burn.
To obtain the longest possible battery pack life,
we suggest the following:
Store and charge your batteries in a cool area.
Temperatures above or below normal room
temperature will shorten battery pack life.
Never store batteries in a discharged condition. Wait
for battery pack to cool and charge immediately.
All batteries gradually lose their charge. The higher
the temperature, the quicker they losetheir charge.
If you store your unit for long periods of time without
using it, recharge the batteries every month or two.
This practice will prolong battery pack life.
WARNING
Do not attempt to disassemble the battery pack.
Fire or injury can result. Upon removal, cover the
battery pack's terminals with heavy duty
adhesive tape. Do not attempt to destroy or
disassemble battery pack or remove any of its
components. Also, never touch both terminals
with metal objects and/or body parts, as short
circuit can result. Keep away from children.
Failure to comply with these warnings could
result in fire and/or serious injury.
CLEANING THE LINE TRIMMER
WARNING
To prevent serious personal injury, remove the
battery pack before servicing, cleaning,
or removing material from the unit.
Remove the battery pack.
Clean the unit using a damp cloth with a mild
detergent.
Do not use any strong detergents on the plastic
housing or the handle. They can be damaged by
certain aromatic oils such as pine and lemon, and by
solvents such as kerosene.
Moisture can cause a shock hazard. Wipe off any
moisture with a soft dry cloth. Use a small brush or
the air discharge of a small vacuum cleaner brush to
clean the air vents on the battery pack housing and
motor housing.
Keep the air vents free of obstructions.
16
GR
H
CZ
RUS
RO
PL

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Clt-1823bp

Tabla de contenido