Denver SC-17 Manual Del Usuario página 5

ENGLISH
Setup – Vox function
The VOX feature allows you to disable the display of the parent unit and activate it when the
baby unit (camera) captures a noise, such as baby's crying. You can set the sensitivity level:
high sensitivity and low sensitivity.
To enable the VOX function follow these steps:
1.Power ON parent unit.
2.Press OK button to enter in the main menu.
3.Press or buttons to select SETUP option then press OK button.
4.Press or buttons to select VOX ON/OFF parameter then press button to enable the
function (ON) or disable the function (OFF).
5.Press OK button to confirm the selection then press button to exit from main menu.
To set the VOX sensitivity level follow these steps:
1.Power ON the parent unit.
2.Press OK button to enter in the main menu.
3.Press or buttons to select SETUP option then press OK button.
4.Press or buttons to select VOX SENSE parameters then press
desired sensitivity level (HI or LOW).
5.Press OK button to confirm the selection then press
If you set high sensitivity (HI) and the LCD panel in the parent unit never switch
OFF, it means that in the room there are noises. Before to set the final value we
suggest to perform some test in order to select the correct value. Usually the
LOW level is correct to switch ON the LCD panel in the parent unit when there
ALERT
are loud noise as crying baby or when he wakes up.
Setup - TV Mode
This parameter allows you to set the TV mode if you connect the parent unit to an external
TV system by using the A/V OUT connector.
To set the TV mode follow these steps:
1.Power ON the parent unit.
2.Press OK button to enter in the main menu.
3.Press or buttons to select SETUP option then press OK button.
4.Press or buttons to select TV MODE parameter then press button to set PAL or NTSC.
5.Press OK button to confirm the selection then press
In most european countries the main TV mode is PAL. In France is supported
too SECAM.
In most american countries the main TV mode is NTSC.
NOTE
Setup – LCD Bright
This parameter allows you to set the LCD panel brightness level in the parent unit.
To set the LCD bright follow these steps:
1.Power ON the parent unit.
2.Press OK button to enter in the main menu.
3.Press or buttons to select SETUP option then press OK button.
4.Press or buttons to select LCD BRIGHT parameter then press
desired (0 – 4).
5.Press OK button to confirm the selection then press button to exit from main menu.
button to select the
button to exit from main menu.
button to exit from main menu.
or to set the level
ENG 6
Main Menu – TV OUT
The parent unit has an AV OUT connector to connect the appliance to an audio video device
as TV or VCR. In the packaging there is available the audio/video cable. To connect the parent
unit to an external TV system follow these steps:
1.Connect the cable to AV OUT connector available in the right side of parent unit.
2.Connect the 3 RCA connectors (yellow, red and white) to audio/video INPUT in the TV or
VCR:
•The yellow connector is the VIDEO signal.
•The red and white connectors are the stereo audio signal.
3.Power ON the parent unit.
4.Press OK to enter in the main menu.
5.Press or buttons to select TV OUT then press OK button. The LCD panel
in the parent unit will turn OFF and the images will be displayed on TV
screen.
To turn ON the LCD panel in the parent unit follow these steps:
1.Press OK button to enter in the main menu.
2.Press or buttons to select LCD OUTPUT option then press OK button.
The LCD panel in the parent unit will turn ON and you can disconnect the
audio/video cable.
To restore the LCD Panel view you can also turn OFF the parent unit and power
ON it again.
NOTE
Baby Unit – description
This chapter provides a complete description of the Baby Unit functions.
2
3
1
4
1.Antenna
2.InfraRED LED for night vision
3.Lens
4.Microphone and speaker
5.DC Input and power LED
6.Power ON/OFF button
Baby Unit - Batteries
The Baby Unit supports two power systems:
•5VDC – 1.000 mA power adapter available in the packaging.
•3 x AAA standard batteries not included in the packaging.
ENGLISH
5
6
Base with batteries compartment
ENG 7