Denver SC-17 Manual Del Usuario página 6

ENGLISH
To power the camera with batteries please follow these steps:
1.Disconnect the power adapter from Baby Unit and from the power
socket.
2.Open the battery door available in the Baby Unit bottom side (see
the picture).
3.Insert 3 x AAA standard batteries by checking that "+" and "-" marks
match the symbols in the batteries compartment.
4.Close the battery door.
Baby Unit - Pairing
The Baby Unit can communicate with the Parent Unit by using a wireless connection based on
2,4 GHz frequency. To skip interferences or detection from other wireless devices it is necessary
to pair the units. This operation is necessary only one time at the first use or if you want to
change or add other wireless cameras.
To pair the Baby and the Parent Unit please follow these steps:
The pairing phase must be completed in 30 seconds. Because it is a short time,
we suggest to perform the pairing phase by taking Parent and Baby units near
you. When you finish the pairing phase you can install the Baby Unit in the final
NOTE
location.
1.Connect the 5VDC – 1.000 mA power adapter to Parent Unit and fit it in a compatible power
outlet.
2.Power ON the Parent Unit.
3.Press or buttons to select the channel (CH:1, CH:2, CH:3 or CH:4).
4.Connect the 5VDC – 1.000 mA power adapter to Baby Unit and fit it in a compatible power
outlet.
5.Press and hold pressed the power ON/OFF button for 5 seconds, the power LED will flash.
The pairing phase is started and you have around 30 seconds to finish it.
6.Whit a thin object press the RESET button available in the back side of Parent Unit. It will
detect the Baby Unit and the LCD panel will show the images captured from the camera.
Pan & Tilt function
The camera supports two orientations: horizontal (Pan) and vertical (Tilt).
Horizontal rientation (Pan)
Batteries
compartment
Vertical orientation (Tilt)
ENG 8
Troubleshooting
This chapter provides some suggestions in order to fix some problem during the installation
or the use of the video baby monitor:
Problem description
Check if the battery is full charge or not.
Check if the power adapter is connected to Parent Unit correctly.
Check if the power adapter is fitted in a compatible power socket
The Parent Unit does not Power
correctly.
ON.
If the power LED is light ON check if the VOX function is enabled
(see VOX function chapter) or TV OUT function is enabled (see TV
OUT chapter).
Check if the power adapter is connected to camera correctly
Check if the power adapter is fitted in a compatible power socket
The Baby Unit does not Power ON.
correctly.
Check the camera without the power adapter by using 3 x AAA
batteries.
Try to change the number of channel.
No video or audio signal.
Repeat the pairing phase. For more information, please refer to
Installation and Pairing chapter.
The pairing phase takes about 30 seconds. If you do not
complete all steps in this time you need to repeat the phase. We
It is not possible to complete the
suggest to perform the pairing phase by taking Parent and Baby
pairing.
units near you. When you finish the pairing phase you can install
the wireless camera in the final location. For more details please
refer to Pairing chapter.
Adjust the volume by pressing
When use Talk & Listen function
please refer to Volume chapter.
the volume is low.
Increase the Baby Unit Volume. For more details please refer to
Main Menu – Baby Unit Volume chapter.
Please check the strength of the radio signal and try to change
the antenna orientation by moving the Baby Unit.
Perfect signal
Low signal
The quality of audio and/or video is
not acceptable.
No signal
Please do not place camera near electromagnetic interferences
source as HiFi speaker, DECT/Cordless Phone and Hi-Voltage
devices.
When camera works in night vision
It is normal because InfraRed light is not visible at human eyes.
the IR lights do not light ON.
The camera is powered by batteries and probably the charge level
On the monitor there are some
is low. Please replace the batteries or remove them and connect
lines and the image is not clear.
the power adapter.
ENGLISH
Solution
buttons. For more details
or
ENG 9