Publicidad
Please read these instructions thoroughly
This product must be assembled and should only be used for
it's intended purpose as described in these instructions. Use
only for domestic cleaning.
Safety reminders
DO NOT pick up hard or sharp objects, matches, hot ashes,
cigarette ends or other similar items.
DO NOT pick up solvent based products or inflammable liquids
such as cleaning fluids, petrol, etc. or other vapors.
DO NOT use the appliance if it appears to be faulty, or either
the cord to the wall bracket or charger is damaged.
DO NOT replace the battery pack with non rechargeable
batteries.
DO frequently clean the dust cup and filter assembly when
picking up fine powder.
DO return the appliance to the wall bracket after use to
recharge the batteries. Occasionally fully discharge the batteries
to obtain maximum battery life.
DO NOT immerse the complete cleaner in liquids.
DO NOT pick up liquids (Dry version only).
Electrical requirements
This Hoover appliance is supplied with a double insulated
battery charger which is only suitable for insertion in a 230v (UK
240v) socket outlet. Ensure that the charger rating label
matches your voltage supply.
Features [Linked to picture 1]
1
Handle
2
On / Off / Boost
3
Four LED indicators for charge residual level
4
Charging LED indicator
5
Dust cup release buttons
6
Suction inlet
7
Retractable bristles
8
Dust cup
9
Charging/Storage base
10 Crevice tool
11 Squeegee tool (Wet & Dry version ONLY)
Unit Storage [Link to pictures 2 & 3]
The product is designed to sit in the charging base on a flat
surface [picture 2] or vertically if wall mounted [picture 3].
For tidy storage wrap excess cord on the back of the charging
base and exit either side or bottom.
TO WALL MOUNT (Tools required: Screwdriver and drill)
1.
Place the charging base against the mounting surface.
Mark the centers of the holes.
2.
Move base then drill 4.8mm holes.
3.
Fit wall plugs.
4.
Reposition base and insert screws, tighten screws and
ensure base is fixed firmly to the wall.
Charging
Place the cleaner into the base, ensuring the shroud covers the
back of the product.
Note: Use only the charger supplied with your cleaner to
recharge the unit.
IMPORTANT: Before first use, charge your cleaner for at least
24 hours.
When charging the cleaner, the power switch must be off.
It is normal for the charger to become warm to the touch when
charging.
If the operating time reduces after repeated use, let the cleaner
run until it stops, then recharge for 24 hours and repeat this
monthly for best results.
Never charge the batteries in temperatures above 37°C or
below 0°C.
How to use
Remove cleaner from storage base, Push the switch to the '1'
position to switch on, for intensive cleaning push the switch to
'Boost'. To turn off move the switch to the '0' position.
Empty and clean the unit and filter after each use or when the
debris or liquid reaches the maximum fill line.
LED indicators [Picture 4]
The charging LED indicator will illuminate red to advise that the
product is charging [a].
When the cleaner is fully charged, the four LED indicators for
charge residual level will light green [b]. When the charge level
is nil, no lights will illuminate. The residual level will be indicated
at all times by the number of green lights.
Accessories [Linked to pictures 5 & 6]
•
Crevice tool [picture 5]
The Crevice tool is stored in the charger base.
•
Squeegee tool (Wet & Dry version only) [picture 1 (11)]
The Squeegee tool is stored in the charger base. Fit the
squeegee tool into the container to assist in collecting
liquids.
•
Retractable Bristles [picture 6]
Ideal for cleaning delicate surfaces such as computer or
piano keyboards. To use: Slide forwards or backwards to
retract.
ENGLISH
Publicidad
