Black and Decker CS355 Manual De Instrucciones página 5

16. Remove adjusting keys and wrenches
Always check that adjusting keys and wrenches are removed
from the tool before operating the tool.
17. Avoid unintentional starting
Do not carry the tool with a finger on the switch. Be sure that
the tool is switched off before plugging in.
18. Use outdoor extension cables
Before use, inspect the extension cable and replace if
damaged. When using the tool outdoors, only use extension
cables intended for outdoor use and marked accordingly.
19. Stay alert
Watch what you are doing, use common sense and do not
operate the tool when you are tired.
20. Check for damaged parts
Before use, carefully check the tool and mains cable for
damage. Check for misalignment and seizure of moving
parts, breakage of parts, damage to guards and switches and
any other conditions that may affect its operation. Ensure that
the tool will operate properly and perform its intended function.
Do not use the tool if any part is damaged or defective. Do not
use the tool if the switch does not turn it on and off. Have any
damaged or defective parts replaced by an authorised Black
and Decker repair agent. Never attempt any repairs yourself.
21. Warning!
The use of any accessory or attachment or performance
of any operation with this tool other than those
recommended in this instruction manual may present a
risk of personal injury.
22. Have your tool repaired by a qualified person
This tool is in accordance with the relevant safety regulations.
Have your tool repaired by an authorised Black and Decker
repair agent. Repairs should only be carried out by qualified
persons using original spare parts; otherwise this may result in
considerable danger to the user.
Additional safety instructions for chopsaws
Always wear regular working gloves while operating this
u
tool.
Keep hands away from the cutting disc. Never cut
u
workpieces that require manual action closer than 15 cm
from the rotating cutting disc.
Do not cut workpieces less than 1.2 mm in thickness when
u
using the cutting disc supplied with this tool.
Do not operate this tool without guards in place.
u
Do not perform any operation freehand. Use the material
u
clamp to clamp the workpiece securely.
(Original instructions)
Never reach in the back of the cutting disc.
u
Always position the tool on a flat, stable surface that is
u
well maintained and free of loose materials, e.g. chips and
cut-offs.
Before using, inspect the cutting disc for cracks or flaws.
u
Discard the cutting disc if a crack or flaw is evident.
Make sure the cutting disc is not contacting the workpiece
u
before the tool is switched on.
In operation, avoid bouncing the cutting disc or giving it
u
rough treatment. If this occurs, stop the tool and inspect
the cutting disc.
Do not operate the tool while standing in line with the
u
cutting disc. Keep other persons away from the work area.
Be aware of cutting chips and the material being cut. They
u
may be sharp and hot. Allow cut off parts to cool before
handling.
The spark deflector becomes hot during use. Avoid
u
touching or adjusting the spark deflector immediately after
operation.
Switch off the tool and wait for the cutting disc to stop
u
before moving the workpiece or changing the settings.
After switching off, never attempt to stop the cutting disc
u
by pressing against the side of the disc.
Do not use cutting fluids. These fluids could ignite or
u
cause electrical shock.
Check that the workpiece is properly supported.
u
Use the cutting discs recommended by the manufacturer
u
only. Never use circular saw blades or any other types of
toothed blades.
The max. allowable speed of the cutting disc must always
u
be equal to or greater than the no-load speed of the tool
specified on the nameplate.
Do not use cutting discs that do not conform to the
u
dimensions stated in the technical data.
Only use cutting discs that conform to EN12413.
u
Ensure that the cutting disc is mounted correctly before
u
use.
Let the tool run at no-load in a safe position for at least 30
u
seconds. If there is a considerable vibration or if any other
defect occurs, stop the tool and check it to determine the
cause.
Do not use cutting discs for side grinding.
u
Do not cut concrete, brick, tile or ceramic materials.
u
Do not cut wood, plastic or synthetic materials.
u
Do not cut cast-iron materials.
u
Never cut magnesium materials.
u
Do not cut electrically live material.
u
Use this tool in a well-ventilated area. Do not operate the
u
tool near flammable liquids, gases or dust. Sparks or hot
chips from cutting or arcing motor brushes may ignite
combustible materials.
ENGLISH
5