Troubleshooting; Protecting The Environment; Technical Data - Black and Decker BDMOW1400 Manual De Instrucciones

ENGLISH
Lubrication
No lubrication is necessary. Do not oil the wheels. They have
plastic bearing surfaces which require no lubrication.
Cleaning
Turn the mower off and let the blade come to a stop. Use only
mild soap and a damp cloth to clean the mower. Clean out any
clippings which may have accumulated on the underside of
the deck. After several uses, check all exposed fasteners for
tightness.
Preventing corrosion
Fertilizers and other garden chemicals contain agents which
greatly accelerate the corrosion of metals.
If you mow in areas where fertilizers or chemicals have been
used, the mower should be cleaned immediately afterward as
follows:
Turn the mower off and unplug mower. Wipe all exposed parts
with a damp cloth.
Maintenance
Your BLACK+DECKER corded/cordless appliance/tool has
been designed to operate over a long period of time with a
minimum of maintenance. Continuous satisfactory operation
depends upon proper tool/appliance care and regular
cleaning.
Warning! Before performing any maintenance on corded/
cordless power tools:
Switch off and unplug the appliance/tool.
u
Or run the battery down completely if it is integral and then
u
switch off.
Unplug the charger before cleaning it.
u
Your charger does not require any maintenance apart from
regular cleaning.
Regularly clean the ventilation slots in your tool/appliance
u
and charger using a soft brush or dry cloth.
Regularly clean the motor housing using a damp cloth. Do
u
not use any abrasive or solvent-based cleaner.
Regularly use a blunt scraper to remove grass and dirt
u
from the underneath of the guard.

Troubleshooting

If your appliance seems not to operate properly, follow the
instructions below. If this does not solve the problem, please
contact your local BLACK+DECKER repair agent.
Warning! Before proceeding, release the bail bar to turn
mower off and wait for the blade to stop.
14
(Original instructions)
Problem Possible cause
Mower will not Cord is not plugged
start. in.
Circuit fuse is blown.
Cord or switch is
damaged.
Grass too long.
Machine functions
Thermal cut out
intermittently. activated.
Machine leaves
Height of cut too low.
ragged finish or
Cutting blade blunt.
motor labours.
Underside of
machine clogged.
Blade fitted upside
down.

Protecting the environment

Z
Separate collection. Products and batteries
marked with this symbol must not be disposed of
with normal household waste.
Products and batteries contain materials that can be
recovered or recycled, reducing demand for raw materials.
Please recycle electrical products and batteries according to
local provisions. Further information is available at
www.2helpU.com

Technical data

Voltage V
AC
Power inpurt
W
No-Load speed min
-1
Height djustment
mm
Blade length cm
Weight Kg
Hand/arm weighted vibration value:
= 2.5m/s , uncertainty (K) = 1.5m/s
2
Sound pressure level at the operator's ear:
L : 82dB(A); K= 2.1dB(A)
PA
Sound power level L
Possible solution
Plug mower into a working
outlet.
Replace circuit fuse. (If the prod-
uct repeatedly causes the circuit
fuse to blow, discontinue use im-
mediately and have itserviced by
an authorised BLACK+DECKER
service center.
Have cord or switch replaced at
an authorised BLACK+DECKER
service center.
Increase the height of
cut and move machine to shorter
grass to start.
Allow motor to cool and increase
height of cut.
Increase height of cut.
Replace the blade.
Check underneath the machine
and clear out as necessary
(always wear heavy duty gloves)
Refit blade correctly.
BDMOW1400 (Type 1)
.
2
: 95dB(A); K= 1.3dB(A)
WA
230
1400
3500
20 - 70
34
14.37