GreenWorks GPW 2300 Guia De Inicio Rapido

INSTALLING THE WHEELS
■ Insert an axle through a wheel, the frame of the
unit, and then a washer.
■ Insert a cotter pin through the hole in the axle to
secure. Repeat for second wheel.
ASSEMBLING THE UPPER PANEL AND SPRAY GUN HOLDER
■ Line up the screw sleeves with the holes in the upper
handle and push through.
■ Insert the screw and turn clockwise with a phillips head
screw driver (not included) until the screw is tight.
ASSEMBLING THE HOSE HOOK
■ Line up the hose hook upper end with the holes on the
back of the upper panel.
■ Insert the hose hook end into the hole and push through.
■ Press the hose hook lower end into the clip on the back
of the upper panel.
ASSEMBLING THE HANDLE
■ Push and hold the button on the handle as you slide the
handle into the slots in the frame.
Missing parts, accessories or need a service center?
Do Not Return to Store
1-855-345-3934.
Call :
www.GreenWorksTools.com
This Quick Start Guide is not a substitute for reading the operator's manual. To reduce the risk
WARNING:
of injury or death, user must read and understand operator's manual before using this product.
2300 PSI PRESSURE WASHER
GPW 2300
USING DETERGENT
■ Put pressure washer detergent in detergent tank.
■ Install blue or black soap nozzle.
■ Squeeze trigger and wait approx.1 minute for soap.
SPRAY TIP
SPRAY TIP APPLICATION
Yellow - Narrow fan tip (15° )
■ The yellow pressure washer tip provides high versatility with its 15 degree angle
tip. Referred to as the washing tip, because it provides adequate pressure to
remove dirt from surfaces, but is designed to not damage many surfaces. This
pressure washer tip is designed for "sweeping" foliage or debris given its wide
15
O
angle. This tip is versatile due to its wide area of cleaning and strong pressure
application.
Green - Narrow fan tip (25° )
■ The green pressure washer tip provides high versatility with its 25 degree angle
tip. Referred to as the washing tip, because it provides adequate pressure to
remove dirt from surfaces, but is designed to not damage many surfaces. This
pressure washer tip is designed for "sweeping" foliage or debris given its wide
25
O
angle. This tip is versatile due to its wide area of cleaning and strong pressure
application.
White - Wide fan tip (40° )
■ The white 40 degree tip, referred to as the "fan" tip creates the widest area of
cleaning with relatively low pressure. This pressure washer tip is best used for
light or delicate cleaning applications. It is recommended for light cleaning on
40
O
wood decks and other soft or delicate surfaces.
Black - Soap spray tip
■ The black soap spray tip, is used for soap application. Soap is applied under low
pressure high volume for optimum performance. Soap cannot be applied under
SOAP
high pressure with this machine.
Turbo Nozzle Tip
■ The nozzle rotates in a zero to 15 degree spray pattern in a circular motion to
break down tough dirt and grime. The spray pattern can cover area of 4 to 8
inches wide, depending on a distance between the tip and the surface being
TURBO
cleaned.
CONNECTING DESIRED SPRAY TIP
■ Pull back the quick-connect collar
■ Push the spray tip into place
■ Push the collar forward
1
2
3
4
5
6
120S
30 S
7
8
NOTE:
AUTO ON/OFF SWITCH: This Pressure washer is equipped with an
Auto Start/Stop feature.
To operate: Set the power switch to the On (I) position. Pump will
A
B
pressurize and shut down immediately.
Once the trigger of the gun is depressed the unit will turn on. Unit
C
will shut off and be in standby mode when trigger is released.
Set-up
Connect garden hose to pressure
washer water intake.
Assemble pressure washer gun to spray
wand.
Insert the uberflex hose into trigger
handle.
Insert the uberflex hose into the pressure
washer.
Turn on water at outlet.
Run water hose for 30 seconds with the
motor in OFF position. This helps drain air
from the tank and lines.
Connect power cord to wall outlet
Extension cord not recommended.
Turn on Pressure Washer
IMPORTANT: Ensure water outlet is On
before turning power On to avoid damage
to the pump.