Product Specifications; Printer Cleaning - Bixolon SPP-R410 Guia De Instalacion

◈ Self-test
Run the self-test when first setting the printer or when encountering a problem, and check the
following.
• Control Circuit, Mechanisms, Print Quality, ROM Version, and Memory Switch Settings
If no issue is found with the printer after running the self-test, examine the other devices or
peripherals and software. This function is independent of such other devices and software.
• Self-Test Instructions
1) Turn the printer power off and close the printer paper cover.
2) Pressing the paper feed button and power button simultaneously turns the printer on.
3) After printing begins, please release the two buttons.
4) To add a printout of the ASCII pattern, press the paper feed button once more.
5) After the ASCII pattern is printed out, the self-test is automatically terminated.

◈ Product Specifications

Item
Printing Method Thermal Printing
Receipt Paper: 90 mm/sec
Print Speed
Linerless Paper: 60 mm/sec
Resolution 203 DPI
Printing
Emulation BXL/POS
Paper End Sensor,
Sensor Paper Cover Open Sensor,
Black Mark Sensor (Optional)
Cutter Type Tear-Bar
Paper Type Thermal Paper
Receipt Paper: Max. Ø57 mm (2.24 in.)
Outer Diameter
Label Paper: Max. Ø56 mm (2.20 in.)
of Paper Roll
Linerless Paper: Max. Ø56 mm (2.20 in.)
Paper
Width 111.5 ± 0.5 mm (4.39 ± 0.02 in.)
Receipt Paper: 0.07 ± 0.005 mm
Thickness Label Paper: 0.07 ~ 0. 15 mm
Linerless Paper: 0.08 ± 0.01 mm
USB, Serial
Interface Bluetooth 4.1 (Classic/LE)
WLAN 802.11 a/b/g/n
※ Note
1) This equipment is indooruse and all the communication hiring are limited to inside of the
building.
2) The switch is the disconnecting device. Turn off switch from any hazard.
◈ Label Printing Function
1. Label Function Setting
Label paper and black mark paper available at the label mode.
• Setting Operations
1) Turn on the printer power.
2) Open the paper cover and press and hold down the paper feed button for longer than two
seconds.
3) After the buzzer tone is emitted, insert paper and close the cover.
4) Repeat the steps above to return to receipt mode.
• Setting Via Memory Switch
1) Please refer to the Unified Utility Manual.
※ Note
The SPP-R410 defaults to receipt mode and the SPP-L410 defaults to label mode.
2. Auto Calibration Function
The label printing function requires the recognition of label paper gaps and black mark
paper black bar in order to print.
If label paper gaps are not properly recognized, use the auto calibration function.
• Auto Calibration Instructions (SPP-R410)
1) Turn the printer power off while in label print mode.
2) Press and hold down the paper feed button and then press the power button.
3) After the following printout is outputted, press the power button to perform auto
calibration.
Auto Calibration: Power Button
Self Test: Feed Button
4) one pages of label paper are outputted when performing auto calibration.
Description
SPP-R410 SPP-L410
Label Paper: 102 mm/sec
Linerless Paper: 76mm/sec
SLCS, BPL-Z™, BPL-C™
Gap Sensor,
Paper Cover Open Sensor,
Black Mark Sensor
Select the mode
◈ Peripherals Connection
※ Note
Refer to the Bluetooth Wireless LAN Manual for detailed information on its connection.
You can check the Bluetooth environment (authentication, encryption, connection mode) and
the wireless LAN environment (IP, SSID, authentication, encryption) via the self-test page.

◈ Printer Cleaning

If the interior of the printer is dusty, print quality can decline.
In such a case, follow the instructions below to clean the printer.
• Make sure to turn the printer power off prior to cleaning.
• As the print head gets very hot during printing, if intending to clean the print head, turn the
printer power off and wait approximately 10 minute before commencement.
• When cleaning the print head, take care not to touch the heated portion of the print head.
→ The print head is susceptible to damage from static electricity, etc.
• Take care not to allow the print head to become scratched and/or damaged in any way.
1) Open the paper cover and remove any paper that may be present.
Use the cleaning pen to clean the printer head in a direction from the center to the outside.
2) Wipe the print head with a cleaning pen.
3) Remove paper dust from the black mark sensor using the cleaning pen.
4) Do not use the printer for 10 minutes after cleaning the printer head until the cleaning
agent of the cleaning pen has completely evaporated and dried.
5) Insert the paper and then close the printer's cover.
◈ WEEE
This marking shown on the product or its literature, indicates that it should not be disposed of
with other household wastes at the end of its working life. To prevent possible harm to the
environment or people from uncontrolled waste disposal, please separate this from other types
of wastes and recycle it responsibly to promote the sustainable reuse of material resources.
Household users should contact either the retailer where they purchased this product, or their
local government office, for details of where and how they can take this item for
environmentally safe recycling. Business users should contact their supplier and check the terms
and conditions of the purchase contract. This product should not be mixed with other
commercial wastes for disposal.
☎ BIXOLON Co., Ltd.
● Website http://www.bixolon.com
● Korea Headquarters
(Add) 7~8F, (Sampyeong-dong), 20, Pangyoyeok-ro241beon-gil,
Bundang-gu, Seongnam-si, Gyeonggi-do, 13494, Korea (ROK)
(Tel.) +82-31-218-5500
● U.S. Office
(Add) BIXOLON America Inc., 3171 Fujita St, Torrance, CA 90505
(Tel.) +1-858 764 4580
● Europe Office
(Add) BIXOLON Europe GmbH, Tiefenbroicher Weg 35 40472 Düsseldorf
(Tel.) +49 (0)211 68
1. Bluetooth & Wireless LAN Connection
1) The printer can be connected to devices
equipped with Bluetooth communication
capacity (PDAs, PCs, etc.).
2) Use the Bluetooth connection function
supported by the device to connect to the
printer.
3) The printer can be connected to other
stations, such as PDAs and PCs supporting
wireless LAN communication in Ad-hoc
mode and AP in Infrastructure mode.
2. Interface Cable Connection
1) Open the Interface Cap
2) Connect the interface cable (optional) to the
cable connector of the printer.