Technical Data - EINHELL TE-SM 2131 Dual Manual De Instrucciones

Sierra de tracción, oscilante y para cortar ingletes
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 72

4. Technical data

AC motor: ................................230-240 V ~ 50Hz
Power: ....................1500 W S1 / 1600 W S6 20%
Idle speed n
: ....................................... 5000 rpm
0
Carbide saw blade: ...........ø 210 x ø 30 x 2.8 mm
Number of teeth: ............................................ 48
Maximum tooth pitch: .............................. 3.2 mm
Swiveling range: ............................ -47° / 0°/ +47°
Miter cut to the left: .................................0° to 45°
Miter cut to the right: ...............................0° to 45°
Saw width at 90°: ............................ 310 x 65 mm
Saw width at 45°: ............................ 210 x 65 mm
Saw width at 2 x 45°
(double miter cut left): ...................... 210 x 35 mm
Saw width at 2 x 45°
(double miter cut right): ................... 210 x 20 mm
Workpiece length, min.: .......................... 180 mm
Weight: .......................................... approx. 13 kg
Laser class: ...................................................... 2
Wavelength of laser: ................................ 650 nm
Laser output: ........................................... ≤ 1 mW
Protection class: ............................................ II/
Operating mode S6 20%: Continuous operation
with idling (cycle time 10 minutes). To ensure that
the motor does not become excessively hot, it
may only be operated for 20% of the cycle at the
specifi ed rating and must then be allowed to idle
for 80% of the cycle.
Danger!
Sound and vibration
Sound and vibration values were measured in
accordance with EN 62841.
L
sound pressure level ..................... 95,1 dB(A)
pA
K
uncertainty ............................................. 3 dB
pA
L
sound power level ..................... 108,1 dB(A)
WA
K
uncertainty ............................................. 3 dB
WA
Wear ear-muff s.
The impact of noise can cause damage to hea-
ring.
The stated vibration emission levels and stated
noise emission values were measured in ac-
cordance with a set of standardized criteria and
can be used to compare one power tool with
another.
Anl_TE_SM_2131_Dual_SPK9.indb 24
Anl_TE_SM_2131_Dual_SPK9.indb 24
GB
The stated vibration emission levels and stated
noise emission values can also be used to make
an initial assessment of exposure.
Warning:
The vibration and noise emission levels may vary
from the level specifi ed during actual use, depen-
ding on the way in which the power tool is used,
especially the type of workpiece it is used for.
Keep the noise emissions and vibrations to a
minimum.
Only use appliances which are in perfect wor-
king order.
Service and clean the appliance regularly.
Adapt your working style to suit the appliance.
Do not overload the appliance.
Have the appliance serviced whenever ne-
cessary.
Switch the appliance off when it is not in use.
Caution!
Residual risks
Even if you use this electric power tool in
accordance with instructions, certain resi-
dual risks cannot be rules out. The following
hazards may arise in connection with the
equipment's construction and layout:
1. Lung damage if no suitable protective dust
mask is used.
2. Damage to hearing if no suitable ear protec-
tion is used.
3. Health damage caused by hand-arm vib-
rations if the equipment is used over a pro-
longed period or is not properly guided and
maintained.
- 24 -
24.10.2019 07:09:27
24.10.2019 07:09:27

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

43.008.60

Tabla de contenido