GreenWorks 24077 Manual Del Usuario página 14

ASSEMBLY
UNPACKING
■ Carefully remove the product and any accessories
from the box.
■ Inspect the product carefully to make sure no breakage
or damage occurred during shipping.
■ Do not discard the packing material until you have
carefully inspected and satisfactorily operated the
product.
■ If any parts are damaged or missing, please call your
Greenworks Tools service centre for assistance.
The blower vac is supplied with some components not
assembled. To assemble these, proceed as follows:
ASSEMBLE AS A MULCHER(Fig.2)
■ Slide the front and rear mulcher tubes together until
locked. (See fig 2)
■ Pull the lock button forward to disengage the gate.
Hold the gate open. (See fig 2.1)
■ Insert the "wedged" end clip of the mulcher tube into
the rear clip. (See fig 2.2). Push the "hooked" end clip
of the mulcher tube into the front clip. (See fig 2.3).
Press the lock button back to engage the mulcher
tube. (See fig 2.4)
■ To remove mulcher tubes, follow the steps (3) (2) (1).
■ Insert the bag adaptor into the blower outlet. Lock the
bag adaptor with the lock button. To remove the bag,
simply press lock button and remove bag. (see Fig.4).
NOTE: It may be necessary to remove the blower tube or
mulcher tubes to clear a blocked tube or impeller.
WARNING:
To prevent serious personal injury, make sure the
switch is in the OFF position, it is unplugged, and
the impellers have stopped before attaching or
removing tubes.
ASSEMBLE AS A BLOWER(Fig.3)
■ Slide blower tube forward until the notched areas on
the blower housing click into the slots on the tube.
INSTALLING BAG WITH SHOULDER HARNESS (Fig. 4)
■ While standing in the operating position adjust the
length to fit the operator's size. Pull the tab to lengthen,
pull the strap to shorten.
OPERATION
CONNECTING THE POWER CORD (Fig. 5)
■ Secure the extension cord to the motor housing using
the notch at rear of blower. This prevents accidental
removal of the electrical cord.
ENGLISH (Original Instructions)
■ Plug the female end of the electrical cord into the
receptacle at the back of the unit.
STARTING/STOPPING THE BLOWER/ MULCHER (Fig. 6)
■ To turn on: Press the switch with ON position.
■ Rotate the dial forward to increase speed.
■ To turn off: Press the switch with OFF position.
IMPORTANT: While in mulching mode the blower MUST
be in high speed position.
HOLDING THE BLOWER/MULCHER
Before operating the unit, stand in the operating position.
Check for the following:
■ Operator is wearing proper clothing, such as boots,
safety glasses or goggles, ear/hearing protection,
gloves, long pants and a long sleeve shirt.
WARNING
To avoid serious personal injury, wear
goggles or safety glasses that comply with
ANSI Z87.1 at all times when operating
this unit. Wear a face mask or dust mask in
dusty locations
WARNING
To prevent serious personal injury or
damage to the unit, make sure the blower
tube or the mulcher tubes and the bag are
in place before operating the unit
OPERATING TIPS (Fig. 7)
■ The bag is installed and zipped closed (when used as
a mulcher).
■ Be sure the bag is zipped closed before operating the
unit.
■ Assure the unit is not directed at anybody or any loose
debris before starting the unit.
■ Verify that the unit is in good working condition. Make
sure the tubes and guards are in place and secure.
■ Always hold the unit with both hands when operating.
■ Keep a firm grip on both the front and rear handle or
grips.
■ To reduce the risk of hearing loss associated with
sound level(s), hearing protection is required.
■ Use the shoulder strap when using unit as a mulcher.
■ Operate power equipment only at reasonable hours—
not early in the morning or late at night when people
might be disturbed. Comply with times listed in local
ordinances. Usual recommendations are 9:00 am to
5:00 pm, Monday through Saturday.
13
.
.