Functional Description - Carrier 40VCI57FQEE Manual De Instalación Y Propietario

REMOTE CONTROLLER OPERATION MANUAL
External View of Remote Controller
Loading of the battery
1. Remove the battery cover;
2. Load the batteries as illustrated. 2 R-03
batteries, resetting key (cylinder); be sure
that the loading is in line with the "+"/ "-";
3. Load the battery, and then close the cover
again.

Functional description

1. Power-up and Show All: the LCD display shows all symbols in this
function. 3s later, it just shows time and the initial time is AM 12:00. The
initial time is adjustable and will be confirmed automatically 10s later.
2. ON/OFF Button: press the button for power on. The initial default
mode is SMART; otherwise it will be the mode before power OFF. Press
OFF button after power on.
3. SMART Button:
(1) SMART button is always operable during power ON/OFF;
(2) Press SMART button to execute power OFF in SMART mode;
(3) In OFF and other modes, press SMART button to enter initial default
setting of SMART mode. LCD setting temperature is not displayed;
(4) In SMART mode, press TEMP. +/- button to show the setting
temperature.
4. COOL Button, HEAT Button and DRY Button
(1) When the remote controller in ON, press COOL button, HEAT button
and DRY button to execute COOL mode, HEAT mode and DRY mode.
(2) For initial power-up, temperature and fan speed will be displayed
as follows when entering each mode, otherwise parameters set last time
will be displayed;
Mode SMART
Initial TEMP. 24°C
Mode SMART
Initial Fan Speed AUTO
5. FAN Mode
(1) During power OFF, press "HEALTH" button or "FRESH" button
to enter FAN mode with low fan speed. Meanwhile, the HEALTH or
FRESH icon will be displayed on the screen.
(2) Temperature is not displayed in FAN mode.
(3) Auto fan speed is not available while switching fan speed in FAN
mode.
6. FAN SPEED Button:
(1) In other modes except for Fan mode, LOW, MED, HI and AUTO fan
speed is adjustable, switching sequence is: LOW-MED-HIAUTO-LOW.
LOW MED
(2) After TURBO or QUIET is set, press TURBO button to show
TURBO on the screen to adjust fan speed with
then press "FAN SPEED" button to exit; press QUIET button to show
on the screen to adjust fan speed with fan speed icon
press "FAN SPEED" button to exit. To cancel TURBO and QUIET, press
TURBO and QUIET buttons respectively, TURBO and QUIET icons
will disappear and set the fan speed to chosen level.
(3) This button does not work during power OFF.
7. TEMP. +/- Button:
(1) This button does not work in FAN mode;
(2) Temperature adjustment range in SMART, HEAT, COOL and DRY
mode: 16 ~30°C.
(3) Press and hold "TEMP. +/-" button, the temperature changes once;
long press the button, the temperature changes rapidly.
8. Four-side Embedment
(Available for some models):
(1) Initial position of all modes for first power on:
Mode SMART
Four-side Show all
Embedmen
SWING Angle Position 3 Position 5
(2) After power o, press "Four-side Embedment" button for the first time
and the recycle approach is as follows: four-side simultaneous control
of Four-side Embedment → Four-side Embedment 1 → Four-side
Embedment 2 → Four-side Embedment 3 → Four-side Embedment
4 → Four-side simultaneous control of Four-side Embedment.
2 2
HEAT COOL DRY
24°C 24°C 24°C Setting temperature
is not showed.
HEAT COOL DRY
LOW HI AUTO
LOW, MED and HI fan speed
options appear
HI AUTO FAN SPEED
,
HEAT COOL DRY
Show all Show all Show all
Position 3 Position 3
FAN
FAN
LOW
, then
FAN
Show all
Position 3