Carrier 40VCI57FQEE Manual De Instalación Y Propietario página 3

(3) When pressing "Four-side Embedment" button to select air
deflector, the selected air deflector flashes. Press "Up-and-down Angle"
button to adjust angle of air deflector.
9. Up-and-down SWING Angle:
1: Position 1; 2: Position 2; 3: Position 3; 4: Position 4;
5: Position 5; 6: Position 6 (reserved)
Recycle approach: Position 1→Position 2→Position 3
→Position 4→Position 5→AUTO→Position 1
Auto swing: 1→2→3→4→5→4→3→2→1 is displayed circularly.
10 Right-and-left SWING Angle (Available for some models):
Recycle approach: 34 displayed (Position 1)→25 displayed
(Position 2)→16 displayed (Position 3)→1 displayed
(Position 4)→2 displayed (Position 5)→5 displayed
(Position 6)→6 displayed (Position 7)→Auto swing
Auto swing approach: 1→2→3→4→5→6→5→4→3→2→1
are displayed circularly.
11. HEALTH AIRFLOW (Available for some models):
Press "HEALTH AIRFLOW" button to display
Each air deflector rotates to exhaust air. Meanwhile, up-and down
SWING angle displays AUTO SWING. Press it again to cancel
HEALTH AIRFLOW.
12. SLEEP:
(1) Works during power on.
(2) The SLEEP time is fixed to 8 hours and is not adjustable.
(3) It does not work in FAN mode. Set TIMER ON or TIMER OFF after
setting SLEEP function, to cancel SLEEP mode. In TIMER mode,
SLEEP mode cannot be set. SLEEP function can be set from TIMER
OFF to TIMER ON, TIMER OFF and SLEEP function have priority in
canceling each other.
13. HEALTH:
(1) During power-on or power-OFF, press "HEALTH" button to display
icon on LCD display, and press "HEALTH" button again to cancel.
(2) During power-OFF, press "HEALTH" button to enter Fan mode, start
low wind and HEALTH function, display icon
(3) Switch among modes, and keep HEALTH function.
(4) If HEALTH function is set, power OFF and then ON to stay in
HEALTH mode.
14. ECO:
(1) Press ECO button and the display will show
(2) ECO works under all modes; it remains active under all modes.
(3) ECO function is retained even in POWER ON or POWER OFF
15. Turbo/Quiet:
(1) Press button "Turbo", to display TURBO on remote LCD to
display icon of fan speed; Press button "Quiet", to display
icon QUIET on remote LCD display; press <command button is
missing here> to display icon
(2) Turbo and QUIET functions cannot exist at the same time; one of
them will replace the other.
(3) If Turbo function is set, press "SLEEP" button to exit turbo setting.
SLEEP function cancels Turbo function. At the same time, the icon
TUEBO disappears and
is shown; to choose QUIET function
during sleep, press button "SLEEP"
(4) This function works with both modes COOL or HEAT.
(5) Turbo/QUIET functions are not stored when you switch through
modes, or turn ON or OFF.
16. IFP:
(1) Press "IFP" button, to display
"IFP" button again to cancel.
(2) Press "Follow/Evade" button, to display
press it again, to display insert to activate Evade. Press it the third
time to cancel.
(3) If follow/evade functions are set, air-outlet angle will follow the
movement of people, so after setting these functions, Four-side
Embedment icons in all sides, up-and-down SWING and left-and right
SWING icons will disappear.
icon on LCD display.
.
ECO .
of fan speed.
IPF , IFP function is set, and press
AUTO
insert to activate Follow;
(4) If air conditioner is in HEALTH airflow mode, and follow/evade
function is set, HEALTH airflow function is cancelled, Four-side
Embedment, up-and-down SWING and left-and-right SWING icons will
disappear.
17. FRESH:
(1) FRESH function works during ON or OFF. When air conditioner is
OFF, press "FRESH" button, to display icon
Fan mode and low speed. Press "FRESH" button again to cancel this
function.
(2) After FRESH function is set, ON or OFF functions can work.
(3) After FRESH function is set, mode switch function can work.
18. 10°C Heating Function and °C/°F function
Press "MENU/°F" button to set 10°C Heating function and °C/°F
function. 10°C Heating Function works only with HEAT mode, and not
with ON or OFF modes.
19. HEATER:
(1) When HEAT mode is chosen and
pressing "HEATER" button can cancel and set HEATER function.
(2) Auto mode will not start HEATER function automatically, but can set
or cancel HEATER function.
20. Timer:
(1) TIMER ON
• Press "TIMER ON" button. Character On flashes on LCD. Press
"+/-" button to adjust, then press "CONFIRM" button to confirm. If
"CONFIRM" button is not pressed within 10s TIMER ON function is
cancelled.
• If time of TIMER ON is the same as that of clock at present, character
"ON" will keep flashing and will not be set. It is necessary to readjust
time.
• When the time of TIMER ON ends, the setting time and character "ON"
disappear.
(2) TIMER OFF
Press "TIMER OFF" button. Character On flashes on LCD. Press
"+/-" button to adjust, then press "CONFIRM" button to confirm, if
"CONFIRM" button is not pressed within 10s TIMER OFF function is
cancelled.
If time of TIMER OFF is the same as that of clock at present, character
"OFF will keep flashing and will not be set. It is necessary to readjust
time.
• When the time of TIMER OFF is end, the setting time and character
"OFF" disappear.
(3) TIMER ON/OFF
• After TIMER ON/OFF is set, remote will automatically judge sequential
order of ON/OFF. Arrow indicates the one performed first and the one
performed second.
• After the time of clock performed first ends, corresponding characters
of timer "ON/OFF" disappear.
• If time of TIMER ON is the same as that of TIMER OFF, it won't be
confirmed. It is necessary to readjust time and confirm again.
(4) After the Timer is set, the display shows Timer setting first and then
displays the current time. When Timer is active, character "ON/OFF" is
always active.
21. Button +/-:
• Press button "+/-", time will change in 1 min intervals. Long press the
button to change time quickly.
22. Clock:
• Press clock button. Characters 'AM" or "PM" start flashing indicating
that clock can now be adjusted. Adjust the clock and press "CONFIRM"
to set the time.
• This mode operates both in ON/OFF
23. LIGHT:
No display on remote controller LCD, which is processed by indoor unit.
24. RESET:
Perform one power on reset operation when RESET button is pressed.
25. LOCK:
Press Lock button to display Lock icon on LCD. Buttons on remote
controller cannot be used. Press button lock again to unlock.
26. CODE: Function reserved.
27. INQUIRE Function reserved.
3
on LCD display to enter
is displayed on LCD display,