Cleaning And Maintenance - KIKKA BOO BON VOYAGE Manual De Instrucciones

INSTRUCTIONS FOR USE AS A "GROUP 0" CAR SAFETY SEAT (FROM BIRTH TO 9 KGS APPR.)
Step 1. For Group 0, the safety seat must only be used in the most reclined Position (see Fig. 1/a).
The safety seat must never be used in any other position (Fig. 1/b). To adjust the reclining position of the safety seat, pull the red handle (J) forward until
the most recline forward position.
Step 2. The seat must always be rear facing (Fig. 3). If your car has an airbag on the Passenger seat,
the safety seat must only be used on the rear seats in the vehicle (Fig. 1/c.).
Step 3. Secure the safety seat onto the car seat using the car seat belt (see Fig. 3).
Step 4. Pass the lap part of the seatbelt under the base of the safety seat into the two points marked by a blue label (A) and fasten the clip to the
corresponding buckle (M).
Step 5. Pass the upper diagonal part of the belt in the metallic guide (B).
Step 6. Take the red Lock-o clip (D) and attach it to the shoulder belt directly above the buckle (Fig. 4). Step 7. Make sure that the belt is not twisted and
strongly tightened before the Lock-o clip is attached.
INSTRUCTIONS FOR USE AS A "GROUP I" CAR SAFETY SEAT (FROM 9 TO 18 KGS)
Step 1. Fasten the Child car seat in forward facing position on either the passenger or rear seat of your
car using the 3 point belt system which is installed in the car.
Step 2. Pass the 3 point belt system (lap and shoulder belt) through the red marked openings (Fig. 4)
(K1 and K2) and through the upper metallic guide. Fasten the buckle (M) in the lock until a click is heard. (Fig. 5). Step 3. At the same time the lap belt is
pulled through the 2 plastic holes. (Fig. 4).
Step 4. Place and fasten the red Lock-o clip (D) on the shoulder belt directly above the buckle. (Fig. 5).
Instructions for use as a "Group II" car safety seat (from 15 to 25kgs)
Step 1. Fasten the Child car seat in forward facing position on either the passenger or rear seat of your car using the 3 point belt system which is installed
in the car.
Step 2. Separate the safety belt from the connection component, which is placed behind the backpart of the safety seat. (Fig. 8).
Step 3. Sit the child on the car seat, pull out of the seatbelt, thread the shoulder harness of the seat belt under the oxter through bellyband, then through
the guiding hole, then through the safety guiding hook and attach to belt buckle, complete. (Fig. 9

CLEANING AND MAINTENANCE

These instructions are important. Read them carefully and keep for future reference.
Remove the harness system. Remove the seat cover. To replace the cover, keep the product.
IMPORTANT: The seat cover is a safety feature. Do not use the safety seat without its cover. Do not put the child' s safety at risk by using a di erent
replacement cover that has not been approved, as this would reduce the level of protection o ered by the seat.
CARE INSTRUCTIONS: The cover is removable and washable at 30 °C. Line dry only. Machine wash, cold. Do not bleach. Do not iron. Dryclean, any solvent
except Trichlorethylene. Do not tumble dry. If in doubt, consult either the child restraint system manufacturer or the retailer.
1. The cover can be removed and washed with a mild detergent using washing machine or hand wash in 30°C.
2. Do not spin and never tumble dry in an electric clothes dryer, only dry in the air.
3. The harness and plastic parts can be wiped by wet cloth with warm soapy water. Do not use chemical reagent, bleacher or corrosive substances.
4. The cover can be reused after cleaning.
ENGLISH