Before Use; During Use; After Use - SKIL MASTERS 6410 Manual Original

f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are less
likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc., in
accordance with these instructions, taking into
account the working conditions and the work to be
performed. Use of the power tool for operations different
from those intended could result in a hazardous situation.
5) SErVIcE
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts. This
will ensure that the safety of the power tool is maintained.
SaFEtY INStrUctIONS FOr Impact drIllS
GENEral
• This tool should not be used by people under the age of
16 years
• Always disconnect plug from power source before
making any adjustment or changing any accessory
• Wear ear protectors (exposure to noise can cause
hearing loss)
• Use auxiliary handle(s), if supplied with the tool
(loss of control can cause personal injury)
• Use completely unrolled and safe extension cords with a
capacity of 16 Amps (U.K. 13 Amps)
• do not work materials containing asbestos (asbestos
is considered carcinogenic)
• Dust from material such as paint containing lead, some
wood species, minerals and metal may be harmful
(contact with or inhalation of the dust may cause allergic
reactions and/or respiratory diseases to the operator or
bystanders); wear a dust mask and work with a dust
extraction device when connectable
• Certain kinds of dust are classified as carcinogenic (such
as oak and beech dust) especially in conjunction with
additives for wood conditioning; wear a dust mask and
work with a dust extraction device when
connectable
• Follow the dust-related national requirements for the
materials you want to work with

BEFOrE USE

• Always check that the supply voltage is the same as the
voltage indicated on the nameplate of the tool
• Avoid damage that can be caused by screws, nails and
other elements in your workpiece; remove them before
you start working
• Use suitable detectors to find hidden utility lines or
call the local utility company for assistance (contact
with electric lines can lead to fire or electrical shock;
damaging a gas line can result in an explosion;
penetrating a water pipe will cause property damage or
an electrical shock)
• Secure the workpiece (a workpiece clamped with
clamping devices or in a vice is held more securely than
by hand)
• Never use the tool when cord is damaged; have it
replaced by a qualified person
accESSOrIES
• SKIL can assure flawless functioning of the tool only
when the correct accessories are used which can be
obtained from your SKIL dealer
All manuals and user guides at all-guides.com
• Use only accessories with an allowable speed matching

dUrING USE

• Always keep the cord away from moving parts of the tool
• If the drill bit becomes unexpectedly jammed (causing a
• Be aware of the forces that occur as a result of jamming
• Hold power tool by insulated gripping surfaces,
• In case of electrical or mechanical malfunction,
• If the cord is damaged or cut through while working, do

aFtEr USE

• When you put away the tool, switch off the motor and
WHEN CONNECTING NEW 3-PIN PLUG (U.K. ONLY):
• Do not connect the blue (= neutral) or brown (= live) wire
• If for any reason the old plug is cut off the cord of this tool,
USE
• On/off 4
• Switch locking for continuous use 5
• Speed control for smooth starting 6
• Maximum speed control 7
• Changing direction of rotation 8
• Normal drilling versus impact drilling 9
• Changing bits 0
• Adjusting drilling depth !
• Holding and guiding the tool @
8
at least the highest no-load speed of the tool
sudden, dangerous reaction), immediately switch off the
tool
(especially when drilling metals); always use auxiliary
handle F 3 and take a secure stance
when performing an operation where the cutting
accessory may contact hidden wiring or its own
cord (a cutting accessory contacting a "live" wire may
make exposed metal parts of the power tool "live" and
could give the operator an electric shock)
immediately switch off the tool and disconnect the plug
not touch the cord, but immediately disconnect the plug
ensure that all moving parts have come to a complete
standstill
in the cord of this tool to the earth terminal of the plug
it must be disposed of safely and not left unattended
With wheel C the maximum speed can be adjusted from
low to high
- switch on the tool
- lock the switch
- turn wheel C to select maximum speed
- when not properly set in left/right position, switch A
cannot be activated
! change direction of rotation only when tool is at a
complete standstill
! select drilling function only when tool is switched
off and plug is disconnected
- insert the bit as deep as possible in the chuck
! do not use bits with a damaged shank
! only use sharp bits
! while working, always hold the tool at the
grey-coloured grip area(s)
- always use auxiliary handle F 3 (can be adjusted
as illustrated)
- keep the ventilation slots uncovered
- do not apply too much pressure on the tool; let the tool
do the work for you