Spare Parts List - Anest Iwata DDP 120 B.TE Manual De Instrucciones

DPS-70 C - DPS-70 CN DIAPHRAGM PUMPS
EN
9.6 DIAPHRAGM SET DISASSEMBLY
A
Remove the 2 nuts with a 10 mm spanner.
Disassemble the rod by pressing on the screw and by
C
pulling from the opposite side-towards the outside.
Rod
PUSH
Main Body
Remove the O rings and the "Y" packings. Place the
E
"Y" packings to the direction that they open outward.
(See picture)
Open side face outwards
9.7 INTAKE AND EXHAUST VALVE
IMPORTANT: Ensure that the packing is inserted in the seat
before placing the valve seat. If not, it may cause paint leak-
age. Check the direction of the valve seat, making reference
to the figure below.
1. Remove packing, seat and steel ball.
2. Replace worn or damage parts.
IMPORTANT: During the reassembly of the lids on main
body, do not reverse the delivery side with the suction one.
(trade marke is upside)
18
REMOVE THE FOLLOWING PARTS FROM ROD:
B
Nut - Spring washer - Diaphragm holder (out) - O'ring
Diaphragm holder set (in/out) - Diaphragm holder (in)
Rod
Diaphragm (OUT)
Washer
Nut
Diaphragm Holder (IN)
Diaphragm (IN)
O'ring
Diaphragm Holder (OUT)
Hold the flat face of the rod center by means of spanner
and loosen the nut on the side, where the diaphragm
D
has not been removed yet and disassemble as descri-
bed in point b).
TO REASSEMBLE REVERSE THE DISASSEMBLY
F
PROCEDURE.
Lubricate the "Y" packings, the O'ring wiht
lithium grease when fitting to rod.
Tightening pressure of nuts: 5.9 Nm
Packing
Steel Ball
Seat
Packing
Lid
Packing
Steel Ball
Seat
Packing
DPS-70 C - DPS-70 CN DIAPHRAGM PUMPS
10. PAINT PRESSURE REGULATORS PR-5BL / PR-5BLN
10.1 TECHNICAL SPECIFICATIONS
VERSION PR-5BL
Paint Passages Material Aluminium
Weight 850 g
Max. Primary Pressure 7 bar (100 psi)
Max. Flow 15 l/min
Pressure range
3 bar
Fluid Inlet joint G 3/8"
Fluid Outlet joint G 3/8"

10.2 SPARE PARTS LIST

Ref. Description
1 JOINT G3/8"
2 VALVE SPRING
3 CARBIDE BALL #
4 O'RING
5 CARBIDE SEAT #
6 PACKING
7 HEX. NUT
8 BODY •
9 JOINT G1/4"- G3/8"
10 DIAPHRAGM BOLT
11 DIAPHRAGM HOLDER
12 DIAPHRAGM #
13 DIAPHRAGM STOPPER
14 O'RING #
15 SPRING WASHER
16 HEXAGON NUT
17 HEX. SOCKET BOLT
18 ADJUSTING SPRING
19 DIAPHRAGM CAP
20 SPRING STOPPER
21 HEXAGON NUT
22 HANDLE SET
23 RISING PIPE
24 PRESSURE GAUGE
10.3 SETUP OF TWO-WAY VALVE JOINT CONNECTION KIT - OPTIONAL
FOR SIMULTANEOUS USE OF 2 SPRAY GUNS, AVAILABLE IN 2 DIFFERENT VERSIONS. (Aluminium and Stainless Steel)
2
1
STEP:
STEP:
PR-5BLN
Stainless Steel
1020 g
# Parts subjects to wear.
• Marked parts differt amoung: Aluminium, Stainless Steel.
3
STEP:
EN
19