Descargar Imprimir esta página
Westinghouse PT10475 Manual De Instrucciones
Westinghouse PT10475 Manual De Instrucciones

Westinghouse PT10475 Manual De Instrucciones

Ocultar thumbs Ver también para PT10475:

Publicidad

Enlaces rápidos

All manuals and user guides at all-guides.com
INSTRUCTION MANUAL
JIG SAW
PT10475
120
480
W
V
800~3,000
spm
60
4
C
US
Hz
A
Note : Before operating this tool,read this manual and
follow all safety rules and operating instructions.

Publicidad

loading

Resumen de contenidos para Westinghouse PT10475

  • Página 1 All manuals and user guides at all-guides.com INSTRUCTION MANUAL JIG SAW PT10475 800~3,000 Note : Before operating this tool,read this manual and follow all safety rules and operating instructions.
  • Página 2: General Power Tool Safety Warnings

    All manuals and user guides at all-guides.com SAFETY GUIDELINES - DEFINITIONS It is important that you read and understand this manual. The information it contains relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols below are used to help you recognize this information. DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
  • Página 3 All manuals and user guides at all-guides.com GENERAL POWER TOOL SAFETY WARNINGS When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock. If operating a power tool in a damp location is unavoidable, use a ground fault circuit interrupter (GFCI) protected supply.
  • Página 4 All manuals and user guides at all-guides.com GENERAL POWER TOOL SAFETY WARNINGS Maintain power tools. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may a ect the efic power tool’s operation. If damaged, have the power tool repaired before fáb use.
  • Página 5 All manuals and user guides at all-guides.com JIG SAW SAFETY WARNINGS Your risk from these exposures varies, depending on how often you do this type of work. To reduce your expose to these chemicals: work in a well-ventilated area, and work with approved safety equipment, such as those dust masks that are specially designed to filter out microscopic particles.
  • Página 6 All manuals and user guides at all-guides.com JIG SAW SAFETY WARNINGS SYMBOLS • The label on your tool may include the following symbols. The symbols • and their definitions are as follows: • V ---------volts A--------amperes • Hz--------hertz W-------watts Min-------minutes -------alternating current •...
  • Página 7 All manuals and user guides at all-guides.com OPERATING INSTRUCTIONS WARNING: Before attempting any of the following operations, make sure that the tool is switched o and unplugged and that the saw blade has stopped. Used saw blades can be hot. INSTALLING A BLADE This jig saw accepts both T shank and universal blades •...
  • Página 8 All manuals and user guides at all-guides.com OPERATING INSTRUCTIONS • Bevel angles are marked on a scale (15) located on the side of the shoe (Fig. D) • Slide the base toward the rear of the jigsaw and align the bevel angle index mark (16) with the desired bevel angle on the shoe.
  • Página 9 All manuals and user guides at all-guides.com OPERATING INSTRUCTIONS NOTE: The orbital setting button will “click” at each of the four positions. Slide the orbital button slightly forward or backward until it locks into place. a de INSTALLING THE VACUUM ADAPTOR To reduce the amount of loose sawdust produced while cutting;...
  • Página 10: Troubleshooting

    All manuals and user guides at all-guides.com OPERATING INSTRUCTIONS When circle cutting, adjust rip fence so that distance • from blade to hole in fence arm is at the desired radius and tighten screws. Place saw so that the hole in fence arm is over centre of circle to be cut (drill hole for blade or cut inward from edge of material to get blade into position).
  • Página 11: Service Information

    All manuals and user guides at all-guides.com MAINTENANCE Use only mild soap and damp cloth to clean the tool. Never let any liquid get inside the tool; never immerse any part of the tool into a liquid. IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by a, y authorized service centres or other qualified service personnel, always using...
  • Página 12 All manuals and user guides at all-guides.com PART LIST DESCRIPTION Leftenclosure Tappingscrew ST3.9X19 Tappingscrew ST3.9X39 Foot base Fixingplate AdjustingScrew M4X16 Torsion-spring Eccentricwheel Support pin Rollersupport Sawblade Fingerguard Spring Front bearing Plungerassembly Back bearing Bush Gear Counterbalance Pendulum bar Connectingplate Closing ring Washer Needlerollerbearing •...
  • Página 13: Exploded View

    All manuals and user guides at all-guides.com EXPLODED VIEW das. lor, sté ejor aga.
  • Página 14 All manuals and user guides at all-guides.com...