Bebecar ACT EasyLock Manual De Instrucciones página 13

GB
READ THESE INSTRUCTIONS CAREFULLY BEFORE
USE AND KEEP THEM FOR FUTURE REFERENCE
YOUR CHILD'S SAFETY MAY BE AFFECTED IF YOU DO NOT FOLLOW THESE INSTRUCTIONS
WARNING: This pushchair has been designed to be operated as shown in the instructions supplied.
1 - TO UNFOLD: When opening the pushchair first adjustable handle by pressing the two buttons simultaneously and
rise the handle bar ensure that the handle is in the horizontal position as indicated in the figure.
2 - Pull handle of pushchair upwards. To engage the secondary lock press down on the plastic pedal at the rear of the
pushchair with your foot.
NB: Check security of the pushchair by pulling on handle and pushing right and left moulding as shown.
3 - STEERING - NON-STEERING: The front wheels can be used in either mode.
Slide lever (on both sides of chassis) to the upwards position for steering, as indicated in the figure.
For non-steering wheels press red button and lever will slide in a downward position.
NB: When using your pushchair on rough ground we recommend non-steering mode.
4 - BRAKE OPERATION: To apply brake, press down on pedal.
5 - To release brake, pull up the pedal.
6 - ADJUSTABLE HANDLE HEIGHT:Press the side button and simultaneously rise or lower the handle bar as required.
7 - ADJUSTABLE HANDLE POSITION: Press the side button and simultaneously rise or lower the handle bar as
required.
8 - TO REMOVE THE REAR WHEEL: Press lever downwards and at the same time pull the wheel away from the axel
housing.
9 - TO FIT THE REAR WHEELS: Place axel in axel housing and press inwards.
Check by pulling wheel to confirm latching of the axel.
10 - TO REMOVE THE FRONT WHEEL:
button is in a upwards position.
Press side button and at the same time pull the wheel away from the front leg.
11 - TO FIT THE FRONT WHEELS:
upwards position.
Press button and at the same time push wheel housing into front leg, until it locks into position.
Check by pulling wheel to confirm latching of the wheel housing.
12 - REAR SUSPENSION SYSTEM: Adjustable in two positions. With brakes applied, use foot to make adjustment.
POSITION "A" — Release suspension moulding as showed in the figure for a soft option for the young infant.
POSITION "B" — Press down on suspension moulding, for a strong but comfortable setting for the larger child.
13 - TO FIT CARRYCOT: Place carrycot base on chassis attachment device "easylock". Lock will automatically engage.
Warning: Check that the pram body attachment devices are correctly engaged before use.
TO REMOVE CARRYCOT: Push in button on base of the carrycot and simultaneously lift carrycot away from
chassis frame.
14 - TO FIT SEAT: Seat may be forward or rear facing. Place seat on chassis attachment devise "easylock". Lock will
automatically engage.
TO REMOVE SEAT: Push in button on both side of seat unit and lift seat away from chassis frame.
15 - TO FIT AUTO SEAT: Place auto seat on chassis attachment devise "easylock". Lock will automatically engage.
Warning: Check that the auto seat attachment devices are correctly engaged before use.
TO REMOVE AUTO SEAT: Push in button on front of seat unit and lift auto seat away from chassis frame.
16 - FOLD PUSHCHAIR:
a) First press the side button of handle and simultaneously lower the handle bar.
b; c) Then press red button and simultaneously lift handle on primary lock as indicated.
d) Then operate secondary lock upwards as indicated.
e; f ) Finally pull primary locking handle upwards, and simultaneously push main handle downwards until the chassis
locks into the folded position.
Not to do so may cause damage and render your guarantee void.
N.B. The front wheels of this chassis can only be removed if the steering
N.B. The front wheels of this chassis can only fitted if the steering button is in a
Warning: Check that the seat unit attachment devices are correctly engaged before use.
N.B: Please remember to lock the swivel wheels in the non-steering mode before folding chair.
NB: Check if both brakes are locked.