Publicidad
Idiomas disponibles
Idiomas disponibles
Firmware update
It is possible to update equipment firmware carrying out the following procedure:
1)
Bring DIP 10 to ON to activate buzzer operation
2)
Bring DIP 8 to ON
3)
Press the RESET button, the buzzer goes off for a few seconds and then shuts off
4)
After about ten seconds, as soon as the buzzer goes off again, bring DIP 8 to OFF
5)
After approximately 5 seconds press the RESET button again
6)
Bring DIP 10 to OFF to silence the buzzer
7)
Connect the USB cable between the board and the PC; update using the FWIN software installed on the PC
8)
At the end of the update, disconnect the USB cable and press the RESET button
9)
Bring DIP 10 to ON to enable buzzer operation
Remote controls
Foggy handles a maximum of 16 remote controls and for each remote control it is possible to singularly enable the
4 combined functions described below:
Key 1: Activates smoke dispensation (with system entered by Key 2 or by ARM inlet).
•
Functioning in demo mode (the activation lasts 60")
•
Functioning in normal mode (impulsive control).
2
1
Key 2: Deactivates smoke dispensation (impulsive control)
5
Key 3: System insertion (impulsive control), as by ARM inlet imbalance.
3
4
If the system results to be already activated by the imbalance of the ARM inlet, the commands
sum up, in this case, to deactivate the system, it is necessary to balance the ARM inlet and
deactivate through key 4 of the remote control. In case of lack or power supply or board
reset, the eventual previous activation through Key 3 is maintained.
Key 4: Deactivate the activation executed by Key 3 of the remote control (impulsive control).
Operation:
During normal system operation, the reception of a command executed by the remote control is signaled on the
display through a symbol made of three horizontal dashes followed by the number of the pressed key.
Only the acquired key can control the associated function and be seen on the display.
The function is carried out in the same moment of the reception of the command, while the display view happens in
sequence to the other eventually already present messages.
Remote controls acquisition:
1. Bring DIP 10 to ON to activate the buzzer and bring DIP 8 to ON to activate remote controls programming mode
2. For each remote control to acquire, configure the address through the dip switches on board and press the keys
relative to the functions one wishes to activate in sequence.
3. The successful acquisition is shown on the display through two horizontal dashes followed by the remote control
number, 0 to 9 for the first ten and A, B,C,D,E,F for remote controls 11 to 16.
4. Repeat step 2 for all the remote controls to acquire
5. Bring DIP 8 to OFF to exit programming mode and act on DIP 10 according to buzzer operation needs.
NOTE: Single keys of the remote control may also be acquired at different times.
Deletion:
1. Bring DIP 10 to ON to activate the buzzer and bring DIP 8 to ON to activate remote controls programming mode
2. Press key 5 and keep it pressed, in sequence press key 4. The buzzer will emit a brief confirmation sound.
3. Release keys 4 and 5.
4. As soon as the buzzer begins to sound again, press key 5 and keep it pressed, press key 4 in sequence. The
buzzer will deactivate and the display will show two horizontal dashes as confirmation of successful deletion.
5. If the procedure described in the previous step is not executed, the buzzer will nevertheless stop sounding after
a few seconds and deletion will not occur. In this case repeat the operation from step 2.
6. Bring DIP 8 to OFF to exit programming mode and act on DIP 10 according to buzzer operation needs.
NOTE: It is not possible to delete the single remote control nor the enabling of a single key.
ATTENTION: DIP 8 in ON also enables the firmware update procedure, therefore avoid executing a board reset
while in remote controls programming mode.
- 41 -
E
N
G
Publicidad
