Triton ETA 300 Instrucciones De Uso Y De Seguridad página 6

e) Maintain power tools. Check for misalignment or
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
ASSEMBLY
ASSEMBLING THE TABLE & RIP FENCE
STEP 1
Using the fasteners from Fastener Bag 1, insert 6 Flange
Nuts (10) into each Long Extrusion (1) as shown in Inset
1, (Fig. 1).
Lay out the two long extrusions and the two short
extrusions as shown in (Fig. 1), making sure that all of the
flange nuts are facing inwards.
Plug the corner blocks of the Short Extrusions (2) into
the ends of the long extrusions and tap fully home with a
mallet (or similar).
STEP 2
Turn the table over (face down, as in Fig. 2) on a flat
surface and loosely attach the Corner Brackets (5), using
the Hex Bolts (11) and Washers (13) into the flange nuts.
(Slide the flange nuts into position using a screwdriver).
Ensure that the two printed corner brackets are bolted
with their correct edges on the same long extrusion
(Fig. 1).
Loosely fit the Brace Brackets (9) to the Braces (4) using
Hex Bolts (11), Washers (13) and Hex Nuts (12). See Inset
2 (Fig 1).
Position the braces about 315mm in from each side of
the frame (Fig. 2) and loosely attach the braces with hex
bolts and washers into the remaining flange nuts. Do not
tighten any of the fasteners yet.
There should be two flange nuts left over. These can be
used later for fitting jigs etc (Fig. 9).
STEP 3
Turn the table face upwards and insert the Scales (3)
between the long extrusions and the brace and corner
GB
brackets. Position them with the 380mm ends hard up
against the short extrusion on the 'map of Australia' side
of the table. Push the scales down until they 'click' into
position, flush with the top face of the long extrusions, as
shown in Inset 3 on (Fig. 1).
Turn the table over (face down). Make sure the corner
brackets are pushed fully home into the corners, and the
plastic corner blocks are still fully inserted into the ends of
the extrusions.
Safety Instructions / Assembly
6
g) Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
5) Service
a) Have your power tool serviced by a qualified repair
person using only identical replacement parts.
This will ensure that the safety of the power tool is
maintained.
Tighten the 8 bolts holding the corner brackets. Do not
over-tighten. (Tighten each pair of bolts a little at a time,
to ensure you don't distort the frame).
Next tighten the 8 bolts holding the brace brackets to the
long extrusions, and finally tighten the 4 bolts through the
braces.
STEP 4
Plug the two smaller Inner Bearings (6) into the corner
blocks below the 380mm scale readings and tighten using
the Countersunk Screws (14) and Hex Nuts (12). The two
longer Outer Bearings (7) are fitted to the corner blocks
near the 1220mm scale readings (Fig. 1).
STEP 5
Take apart the Fence Clamp Assemblies (15) and
reassemble them through the slot in the Fence Assembly
(8) (Fig. 1).
Turn the table face up once again. With the clamp
assemblies loosened, lower the square feet on the clamp
bolts into two of the table corner blocks. Slide the fence
along the extrusions to position it wherever you like, and
tighten the round knob to lock it in place.
ASSEMBLING THE OUTER TRACK
STEP 6
Insert the Coach Bolts (26) through the slots in the Legs
(17), and fit the Height Stops (25) and Round Knobs with
Nuts (27) onto them, as shown in (Fig. 3). Attach the Feet
(18) to the legs using the Leg Plates (19), Hex Bolts (21)
and Nyloc Nuts (22). Note: the raised bumps on the leg
plates must face inwards, touching the legs (see lower
Inset Fig. 3). The feet should face away from the leg slots
(Fig. 3).
Tighten the bolt which passes through each leg until the
feet pivot smoothly. The foot is designed to swing around
on this bolt for easy storage.
STEP 7
Tap the Angled Tube Closers (28) into the bottom of the
legs ensuring they are correctly oriented. Tap the Flat
Tube Closers (29) into the remaining tube ends.