Horizon Global 76336 Instrucciones De Instalación página 4

Always wear SAFETY GLASSES
when installing hitch
1. Remove driver side plastic panel – Using phillips screwdriver, flat head screwdriver and 12mm socket with wrench remove (3) screws, (2) plastic rivets and (2) flange
nuts respectively from driver side plastic panel. Remove plastic panel and return to owner with fasteners.
2. Remove passenger side plastic panel – Using phillips screwdriver, flat head screwdriver and 12mm socket with wrench remove (3) screws, (2) plastic rivets and (1) bolt
respectively from passenger side plastic panel. Remove plastic panel and return to owner with fasteners.
3. Remove metal tab – Using 17mm socket with wrench remove (1) bolt from metal tab on passenger side frame rail. Remove metal tab and return to owner with bolt.
4. Lower muffler – Using an exhaust hanger removal tool, lower muffler by removing (1) rearmost rubber hanger. A spray of lubricant or soapy water on rubber hanger
makes it slide off metal pins more easily. NOTE: Be sure that exhaust is properly supported before removing rubber hanger.
5. Remove plugs and caulking – Using flat head screwdriver remove (3) plastic style plug (on driver side), (2) plastic style plug (on passenger side) and (2) rubber plug from
both side frame rails. Return the plugs to owner. Using utility knife, remove 1/2" caulking from both side frame rails close to forward attachment hole for easier
installation. NOTE: Make sure that vehicle weldnuts are free from rust and debris. Use wire brush to clean the weldnuts if needed.
6. Detach lower fascia tabs - Using flat head screwdriver, remove (2) plastic rivets from lower fascia tab. Detach the tabs from end panel.
7. Install hitch – Raise and align hitch into position over existing weldnuts and loosely install M12 bolts (item 1), conical washer (item 2), flat washer (item 3), and lock
washer (item 4) to the hitch, as shown in Figure 4. Note: Only forward hole on passenger side uses flat and lock washer.
8. Tighten all M12x1.25x35 CL8.8 fasteners with torque wrench to 76 ft -lb (103 N*m).
9. Raise muffler back into position- Reattach the rubber hanger removed in step 5. Remove the support for exhaust.
10. Reattach lower fascia tabs – Using the included cable ties (item 5), reattach the fascia tabs to the hitch cross tube to secure
Note: check hitch frequently, making sure all fasteners and ball are properly tightened. If hitch is removed, plug all holes in trunk pan or other body panels to prevent entry of water and exhaust fumes. A hitch or ball which has been damaged
should be removed and replaced. Observe safety precautions when working beneath a vehicle and wear eye protection. Do not cut access or attachment holes with a torch. This product complies with safety specifications and requirements for
connecting devices and towing systems of the state of New York, V.E.S.C. Regulation V-5 and SAE J684.
©2020 Horizon Global Americas Inc. - Printed in Mexico
Highlander model year: 2020
Vehicle frame rails
2
1
Figure 4
1
2
3
4
Weldnuts
5
3
4
Conical Washer
1
Teeth side
Against hitch
Proper torque is needed to keep the hitch secure to the vehicle when towing.
Sheet 4 of 30 76336NP
Fastener Kit: 76336F
QTY. (6) Bolt M12x1.25x35 CL8.8
QTY. (6) Washer Conical 1/2"
Part No: 01292008
QTY. (1) Washer flat 7/16" heavy
Part No: 1528
QTY. (1) Lock washer ½" plated
Part No: 01129008
QTY. (2) Cable tie 11"
06-18-20 Rev. A