the machine is switched off by means of a
protective circuit.
In a warm environment or after heavy use, the
battery pack may become too hot to permit
charging. Allow time for the battery to cool
down before recharging.
5. TO REMOvE OR INSTALL BATTERy
PACk (See Fig. E)
Depress the Battery Pack Release Button (4) to
remove the Battery Pack (3) from your Hedge
Trimmer. After recharging, insert the Battery
Pack into trimmer's battery port (See Fig. E).
A simple push and slight pressure will be
sufficient until a click is heard. Check to see if
the battery is fully secured.
NOTE: When removing the battery pack, hold
it firmly to avoid dropping and injury.
6. BATTERy STATuS LED'S (See Fig. F )
NOTE: The Status LED's will indicate the
battery condition when the button on the
battery is pressed.
The LED's constantly senses and displays the
battery condition as follows:
12
Press the button "POWERTEST" , the light
button is illuminated.
When the three green lights are illuminated,
the battery is in a highly charged condition.
When two lights (
battery is in a moderately charged condition.
When only one green light (
the battery charge is depleted.
IMPORTANT:
when only one light is illuminated,
your battery is overly discharged, even
though the trimmer may still be capable
of trimming hedge. Continuing to operate
your trimmer with the battery in this
discharged condition may reduce the life
and performance of your battery.
7. STARTING AND STOPPING
BEFORE STARTING yOuR HEDGE
TRIMMER
Remove Blade Sheath (9).
TO START yOuR HEDGE TRIMMER
Your Hedge Trimmer is equipped with both
Rear and Front Switch levers. Both switch
levers need to be depressed for the Hedge
Cordless Hedge Trimmer
All manuals and user guides at all-guides.com
) are illuminated, the
) is illuminated,
Trimmer to start. Depress and hold the Front
Switch Lever (5) and press the Rear Switch
Lever (2) (See Fig. G1).
TO STOP yOuR HEDGE TRIMMER
Move Hedge Trimmer away from cutting area
before stopping.
To stop, release one of the switch levers (See
Fig. G2).
wARNING: If any parts are missing,
damaged or broken, do not operate
your hedge trimmer until all damaged
parts have been replaced or repaired.
Failure to do so could result in serious
personal injury. DO NOT uSE wITHOuT
HANDLE AND GuARD
8. HOw TO uSE yOuR HEDGE TRIMMER
Note that the Front Switch Lever (5) can be
activated on three sides, giving you many
choices for a comfortable grip. Before cutting
an area, inspect it first and remove any
foreign objects that could become thrown
or entangled in the blades. Always hold the
trimmer with both hands and with the blade
away from you before turning it on.
When trimming new growth, use a wide
sweeping action so that the stems are fed
directly into the blade. (See Fig. H& I)
Allow the cutting blades to reach full speed
before cutting. When operating, keep the
cutting blades away from people and objects
such as walls, large stones, trees, vehicles, etc.
If the blade stalls, immediately stop the
trimmer. Release the two Switch Levers (5 &
2) before attempting to clear jammed debris
from the cutting blades.
Wear gloves when trimming thorny or prickly
growth.
Do not attempt to cut stems that are too thick
for the cutting blade.
TOP CuTTING
Use a wide sweeping motion (See Fig. H). A
slight downward tilt of the cutting blades in the
direction of motion gives the best cutting results.
SIDE CuTTING
When trimming the sides of the hedge,
begin at the bottom and cut upwards (See
Fig. I), tapering the hedge inward at the top.
This shape will expose more of the hedge,
resulting in a more uniformed growth.
EN