Important Safety Instructions - Makita 1051D Manual De Instrucciones

ENGLISH
(Original instructions)
1 Button
2 Battery cartridge
3 Knob
4 Scale
5 Pointer
6 Switch trigger
7 Lock-off button
8 Installation bolts
9 Hex wrench
SPECIFICATIONS
Model
Planing width ........................................................ 50 mm
Planing depth ...................................................... 0.5 mm
Shiplapping depth ................................................ 15 mm
–1
No load speed (min ) ............................................ 9,000
Overall length ..................................................... 297 mm
Net weight ............................................................. 2.3 kg
Rated voltage .................................................D.C. 14.4 V
• Due to our continuing program of research and devel-
opment, the specifications herein are subject to change
without notice.
• Specifications may differ from country to country.
• Weight according to EPTA-Procedure 01/2003
Intended use
The tool is intended for planing wood.
Power supply
The tool should be connected only to a power supply of
the same voltage as indicated on the nameplate, and can
only be operated on single-phase AC supply. They are
double-insulated in accordance with European Standard
and can, therefore, also be used from sockets without
earth wire.
General Power Tool Safety Warnings
WARNING Read all safety warnings and all
instructions. Failure to follow the warnings and
instructions may result in electric shock, fire and/or
serious injury.
Save all warnings and instructions for future refer-
ence.
CORDLESS PLANER SAFETY WARNINGS
1. Wait for the cutter to stop before setting the tool
down. An exposed cutter may engage the surface
leading to possible loss of control and serious injury.
2. Use clamps or another practical way to secure
and support the workpiece to a stable platform.
Holding the work by hand or against your body
leaves it unstable and may lead to loss of control.
3. Rags, cloth, cord, string and the like should
never be left around the work area.
4. Avoid cutting nails. Inspect for and remove all
nails from the workpiece before operation.
5. Use only sharp blades. Handle the blades very
carefully.
6. Be sure the blade installation bolts are securely
tightened before operation.
7. Hold the tool firmly with both hands.
4
All manuals and user guides at all-guides.com
Explanation of general view
10 Planer blade
11 Drum cover
12 Side of drum
13 Drum
14 Pan head screws
15 Dust bag
16 Nozzle
17 Fastener
18 Washer
8.
9.
1051D
10. Make sure the blade is not contacting the work-
11. Wait until the blade attains full speed before cut-
12. Always switch off and wait for the blades to
13. Never stick your finger into the chip chute.
14. Do not leave the tool running. Operate the tool
15. Always change both blades or covers on the
16. Use only Makita blades specified in this manual.
17. Always use the correct dust mask/respirator for
SAVE THESE INSTRUCTIONS.
GEA010-1
WARNING:
DO NOT let comfort or familiarity with product
(gained from repeated use) replace strict adherence
to safety rules for the subject product. MISUSE or
failure to follow the safety rules stated in this instruc-
tion manual may cause serious personal injury.

IMPORTANT SAFETY INSTRUCTIONS

GEB064-1
FOR BATTERY CARTRIDGE
1.
2.
3.
4.
5.
19 Thumb screw (A)
20 Edge fence
21 Thumb screw (B)
22 Start
23 End
24 Blade edge
25 Cutting line
26 V groove
Keep hands away from rotating parts.
Before using the tool on an actual workpiece, let
it run for a while. Watch for vibration or wobbling
that could indicate poor installation or a poorly
balanced blade.
piece before the switch is turned on.
ting.
come to a complete stop before any adjusting.
Chute may jam when cutting damp wood. Clean
out chips with a stick.
only when hand-held.
drum, otherwise the resulting imbalance will
cause vibration and shorten tool life.
the material and application you are working
with.
Before using battery cartridge, read all instruc-
tions and cautionary markings on (1) battery
charger, (2) battery, and (3) product using bat-
tery.
Do not disassemble battery cartridge.
If operating time has become excessively
shorter, stop operating immediately. It may
result in a risk of overheating, possible burns
and even an explosion.
If electrolyte gets into your eyes, rinse them out
with clear water and seek medical attention right
away. It may result in loss of your eyesight.
Always cover the battery terminals with the bat-
tery cover when the battery cartridge is not
used.
ENC004-2