Tabla de contenido
Publicidad
FEEDING BOTTLE HOLDING UNIT (IF AVAILABLE)
fig. 21
Hook the feeding bottle holding unit (T9) to the
STORAGE BASKET
fig. 22
The frame is equipped with a capacious storage
basket (T8). To secure it, insert all buttonholes in the proper
hooks and button up the rear strips.
ADDITIONAL TRANSPORT UNITS TO THE FRAME (CARRY
COT, TRANSPORT SEAT, AND INFANT CAR SEAT)
fig. 23
ZIPPY CARRY COT
HOOKING OF THE CARRY COT TO THE FRAME
follows:
fig. 24
Remove the armrest covers (T3) if available,
positioned inside the armrest (F10).
fig. 25
Insert the two stabilizing supports (T7) in the
openings (F11).
WARNING: the stabilizing supports have to be inserted
only when using the frame with the carry cot.
fig. 26
the armrests (F10
fig. 27
WARNING: make sure that the carry cot is always
properly attached on both sides of the frame before use.
UNHOOKING OF THE CARRY COT FROM THE FRAME
fig. 28
Act on the lever (B1
fig. 29
the handle.
HOOKING OF THE HOOD
fig. 30
fig. 31
Wrap the hood (C2) around the handle fastening it
using the suitable press studs.
HANDLE AND HOOD ADJUSTMENT
fig. 32
lateral button (B2
fig. 33
WARNING: to transport the carry cot, always
hold it by the handle.
HOOKING OF THE BLANKET
fig. 34
MAINTENANCE OF THE INTERNAL LINING
fig. 35
It is recommended to remove the internal lining
HUGGY INFANT CAR SEAT
HOOKING OF THE INFANT CAR SEAT TO THE FRAME
to proceed as follows:
fig. 36
If present, remove the stabilizing supports (T7
acting on the proper push-buttons (F12).
WARNING: hold the supports during the ejection.
fig. 37
Remove the armrest covers (T3) if available,
positioned inside the armrest (F10).
fig. 38
attach it to the frame on the armrests (F10), positioning it
30
INSTRUCTIONS
fig. 39
always properly hooked before use.
UNHOOKING OF THE INFANT CAR SEAT FROM THE
FRAME
fig. 40
the infant car seat.
fig. 41
dedicated manual.
TRANSPORT SEAT
HOOKING OF THE TRANSPORT SEAT TO THE FRAME
Before hooking the transport seat to the frame:
fig. 42
acting on the proper push-buttons (F12).
WARNING: hold the supports during the ejection.
fig. 43
F9)
WARNING: when placing the baby, make always sure that
the armrest covers are properly fitted in their seats.
fig. 44
hooked to the frame facing mum or the street.
fig. 45
it in the proper seats on both sides, following the graphical
references available on the structure.
fig. 46
always properly hooked on both sides before use.
UNHOOKING OF THE TRANSPORT SEAT FROM THE FRAME
fig. 47
WARNING: never perform this procedure with baby on
board.
ADJUSTMENT OF THE BACKREST
fig. 48
act on the central device (S2) and bring the backrest to the
wished position.
USE OF THE BUMPER BAR
TRANSPORT SEAT FACING MUM
fig. 49
small handrail (R1) together with its covering.
fig. 50
fig. 51
(S4) on the transport seat.
fig. 52
other side.
TRANSPORT SEAT FACING THE STREET
fig. 53
big handrail (T4) together with its covering.
fig. 54
fig. 55
present under the armrest (F10); to remove it, repeat the
procedure also on the other side.
F9)
WARNING: do not insert the fingers in the openings on
the armrests when performing these procedures.
WARNING: make sure that the infant car seat is
Act on the lever (U1) positioned on the rear side of
If present, remove the stabilizing supports (T7
Insert the armrest covers (T3) in the proper seats.
The transport seat is reversible; therefore, it can be
Hook the transport seat to the frame positioning
WARNING: make sure that the transport seat is
Press the lever (S1) and lift one side of the transport
When the transport seat is facing mum, use the
To hook it, press the levers (S3).
Insert the ends of the handrail in their proper seats
The handrail can be opened on one side or
When the transport seat is facing the street, use the
To hook it, insert the ends in the openings on the
The handrail can be opened on one side or
S3) and
S3)
Publicidad
Tabla de contenido
