General Information On The Operation - Kärcher WD 3 Battery Manual De Instrucciones

Ocultar thumbs Ver también para WD 3 Battery:
Tabla de contenido

Publicidad

Idiomas disponibles
  • ES

Idiomas disponibles

  • ESPAÑOL, página 30
Commissioning
Connect accessories
Illustration
 Push the suction hose into the connection on the
appliance, it snaps in place.
In order to disconnect it, push down with your
thumb and pull the suction hose out.
Illustration
 Connect the handle with the suction hose until it
snaps in place.
 Put both suction tubes together and connect them
with the handle.
Note: Accessories, such as suction brushes (optional)
can be directly attached to the connecting piece and
thus connected to the suction hose.
For convenient working even in tight spaces.
The removable handle can be attached between the ac-
cessories and the suction hose if necessary.
Recommendation: In order to vacuum the floor, attach
the handle to the suction hose.
Illustration
 To remove the handle from the suction hose, press
the button with your thumb and index and remove
handle
Note: Due to removing the handle, accessories can be
directly attached to the suction hose.
Illustration
 Connect the floor nozzle with the suction pipe.
Note: For vacuuming dry dirt or water off the floor - al-
ways work with the insert (brush strip and rubber lip) in
the floor nozzle.
Inserting the battery pack
Illustration
 Push the battery pack from the top into the battery
holder and lock it.
ATTENTION
Damage to the device
Only use battery packs from the KÄRCHER Battery
Power (+) platform with 36 V nominal voltage.
Turning on the Appliance
Illustration
 Position I: Vacuum and blowing function.
Position 0: Appliance is switched off

General information on the operation

ATTENTION
The metal container can become statically charged
when vacuuming large amounts of fine dust particles
and then discharge upon contact.
ATTENTION
The batter holder area must be kept clean.
If there is too much dirt in this area, it is possible
that the battery pack is not inserted/locked into
place.
Similarly, it may be the case that battery pack can
no longer be taken out of the device because the
eject lever can no longer be moved.
Operation
ATTENTION
Always work with an inserted cartridge filter during wet
as well as dry vacuum cleaning!
Dry vacuum cleaning
ATTENTION
Check the filter for damage prior to installation and re-
place as necessary.
Work with a dry cartridge filter only!
Illustration
 Recommendation: To vacuum fine dust, use the
filter bag.
Information filter bag
The filling level of the filter bag depends on the dirt
that is sucked in.
The filter bag needs to be replaced more frequently
while sucking in fine dust, sand, etc.
Clogged filter bags can burst - therefore make sure
to replace the filter bag in a timely manner!
ATTENTION
Vacuum cold ashes only when using a pre-filter.
For information about accessories and spare parts,
please visit www.kaercher.com.
Wet vacuum cleaning
ATTENTION
Do not use a filter bag!
Illustration
 For vacuuming up moisture or liquids pay attention
to the correct floor nozzle insert and connect the
corresponding accessories.
Note: If the container is full, a float closes the suction
opening, and the appliance works at a higher speed.
Switch off the appliance immediately, and empty the
container.
Cleaning hard to reach locations or, where vacuuming
is not possible, like leaves from a gravel bed.
Illustration
 Connect the suction hose to the blower connection,
this will activate the blower function.
Interrupting operation
 Turn off the appliance.
Illustration
 Hook the floor nozzle into the parking position.
Note: If it is necessary to remove the suction head when
work is interrupted, the battery pack may become stuck.
The battery pack is locked in tightly and cannot fall out.
 Turn off the appliance.
Illustration
 Push the battery release button forwards and re-
move the battery pack from the device.
 If necessary, recharge battery pack (see chapter
"Charging battery pack").
Recommendation: Remove the battery pack from the
device after completing the work.
Empty the container
Illustration
 Remove the appliance head and empty the reser-
voir.
Storing the appliance
Illustration
 Store the accessories on the appliance and store
the appliance in dry rooms.
– 8
EN
Blowing function
Finish operation
13

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Wd 3 battery setWd 3 battery premiumWd 3 battery premium set1.629-950.01.629-951.01.629-910.0 ... Mostrar todo

Tabla de contenido