Publicidad
Idiomas disponibles
Idiomas disponibles
Enlaces rápidos
KIT COMPONENTS
• A) Fairing • B) Radio brackets • C) Metal mesh speaker grilles • D) Speaker plates (6x9", 6.5" and blank)
• E) (8) #6 x 1" Stainless screws for grilles (black) • F) (20) #8 x 3/8" Philips screws • G) (4) 1/4-20 x 1/2" Cap screws
A
Metra. The World's Best Kits.
®
Harley Davidson Roadglide
1998-2013
Visit
specific applications
KIT FEATURES
• ISO DDIN radio provision
• Complete inner fairing for a factory look
• Painted high-gloss black
B
C
E
F
MetraOnline.com
MetraOnline.com
for more detailed information about the product and up-to-date vehicle
D
G
© COPYRIGHT 2021 METRA ELECTRONICS CORPORATION
I N S TA L L AT I O N I N S T R U C T I O N S
TABLE OF CONTENTS
(FLT/sharknose fairing)
Fairing Disassembly............................................2-3
Fairing Preparation ............................................4-5
Fairing Assembly ...................................................6
WIRING & ANTENNA CONNECTIONS (sold separately)
Wiring Harness with included interface:
BC-HDSWC-WR
Antenna Adapter: not required
TOOLS REQUIRED
• Panel removal tool • Phillips screwdriver
• T25, Torx screwdriver
• 5/16", 1/2" open ended wrench
• 3/16" Allen (hex) wrench
Attention!
disconnect the negative battery terminal
before installing this product. Ensure that all
installation connections are secure before
cycling the ignition to test this product.
95-HDIF2
With the key out of the ignition,
REV.7/12/21 INST95-HDIF2
Publicidad
Manuales relacionados para Metra 95-HDIF2
Resumen de contenidos para Metra 95-HDIF2
- Página 1 With the key out of the ignition, disconnect the negative battery terminal before installing this product. Ensure that all installation connections are secure before cycling the ignition to test this product. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV.7/12/21 INST95-HDIF2...
-
Página 2: Fairing Disassembly
8. With the panel removal tool, remove the two plastic panel clips holding the inner fairing to the radio bracket. (Figure B) Note: These clips will not be reused on the 95-HDIF2 inner fairing. (Figure D) Continued on the next page 386.257.1187 MetraOnline.com... - Página 3 FAIRING DISASSEMBLY (CONT.) 9. Remove (4) 1/2” nuts securing the radio and inner fairing to the bikes frame. Tilt radio bracket toward the back of bike and remove the bracket and radio assembly. (Figure E) 10. At this point the inner fairing will be loose.
- Página 4 5. Using a 3/16” Allen wrench remove the (Figure B) 2. There are three speaker plate choices (4) bolts holding the OE radio to the included with the 95-HDIF2 inner radio bracket. (Figure C) fairing. (2) 6.5”, (2) 6”x9”, and (2) blank plates for custom speaker sizes.
- Página 5 FAIRING PREPARATION (CONT.) 6. Mount the supplied radio brackets to the aftermarket radio. Note: The location of the radio brackets on the radio chassis will make the aftermarket radio sit further out. This is normal and small adjustments can be made once the inner fairing is installed.
- Página 6 This is a common issue and wire management is order of disassembly to complete the (Figure C) key to getting the outer fairing to match up with the 95-HDIF2 inner fairing. installation. 386.257.1187 MetraOnline.com...
- Página 7 REV. 7/12/2021 INST95-HDIF2...
- Página 8 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recommends MECP certified technicians Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/12/21 INST95-HDIF2...
- Página 9 Asegúrese de que todas las conexiones de instalación estén seguras antes de realizar un ciclo de encendido para probar este producto. Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/12/21 INST95-HDIF2...
- Página 10 8. Utilice la herramienta de retiro de panel para quitar los dos ganchos del panel plástico que sostienen el carenado interno (Figura B) al soporte del radio. Nota: Estos ganchos no se reutilizarán en el carenado interno 95-HDIF2. (Figura D) Continúa en la siguiente página 386.257.1187 MetraOnline.com...
- Página 11 DESARMADO DEL CARENADO (CONT.) 9. Quite las (4) tuercas de 1/2” que fijan el radio y el carenado interno al marco de los neumáticos. Incline el soporte del radio hacia la parte trasera de la motocicleta y quite el soporte y el ensamble del radio. (Figura E) 10.
- Página 12 PREPARACIÓN DEL CARENADO 1. Después de haber quitado el carenado, 3. Utilice (6) tornillos Phillips #8 de 3/8” ponga los carenados de OE y de Saddle por placa y fije la placa del altavoz al 6.5” Tramp uno junto a otro y cambie carenado.
- Página 13 PREPARACIÓN DEL CARENADO (CONT.) 6. Monte los soportes del radio incluidos al radio genérico. Nota: La ubicación de los soportes del radio en el chasis harán que el radio genérico sobresalga un poco. Esto es normal y es posible realizar pequeños ajustes cuando esté...
- Página 14 Este es un problema común, por lo que el en el orden inverso al desensamble para arreglo de cables es fundamental para lograr que el carenado externo se ajuste al carenado interno 95-HDIF2. terminar la instalación.
- Página 15 REV. 7/12/2021 INST95-HDIF2...
- Página 16 Log onto www.installerinstitute.edu or call 386-672-5771 for more information and take steps toward a better tomorrow. Metra recomienda MECP técnicos certificados Metra. The World’s Best Kits. MetraOnline.com ® © COPYRIGHT 2021 METRA ELECTRONICS CORPORATION REV. 7/12/21 INST95-HDIF2...