Operation Of The Device - YATO YT-3617 Manual Del Usuario

All manuals and user guides at all-guides.com
GB
manual.
During work, it is necessary to wear protective goggles; it is recommended to use gloves and protective uniform.

OPERATION OF THE DEVICE

Before each use of the machine, make sure that no element of the pneumatic system is damaged. If any damage has been
observed, it is necessary to replace the damaged element with new elements of the system which are not damaged.
Before each use of the pneumatic system, it is necessary to dry the condensed humidity inside the machine, the compressor and
the pipes.
Connection of the machine to the pneumatic system
The drawing presents the recommended connection of the machine to the pneumatic system. The presented connection will
guarantee the most effective use of the tool, and will prolong its durability.
Place a couple of drops of SAE 10 viscosity oil to the air inlet.
Screw tightly to the thread of the air inlet a proper adapter that makes it possible to connect the air supply hose (II)
Install a proper adapter on the driver of the machine. Use solely the equipment which is adapted for operation with percussive
devices.
Wherever it is possible, adjust the pressure.
Connect the machine to the pneumatic system using a pipe of the internal diameter 3/8". Make sure, the resistance of the pipe is
at least 1.38MPa. (III)
Turn the device on for a few seconds to make sure it does not emit any irregular sounds or vibrations.
Installation and replacement of the equipment
Using the ring, screw down the protection for broken rivet stems (IV). It is prohibited to use the riveting machine without the
protection.
Install a header which is appropriate for the given task (V). The head must be selected in accordance to the length and diameter
of the applied rivets. It is prohibited to use the riveter without a head. In the case of the YT-3618 riveting machine, before work with
rivets whose diameter is 6.4 mm can commence, it is necessary to install jaws with a holder and a pusher, which are appropriate
for tasks with rivets of this diameter. In order to do that, the protection of the head must be dismantled (VI). Then, dismantle the
holder of the jaws with the pusher and the jaws themselves and replace them with jaws and a pusher which are appropriate for
tasks with rivets whose diameter is 6.4 mm. The sub-assemblies must be installed in accordance to the order presented in (VI).
Al threaded connections must be tightened tightly.
Work with the riveting machine
Drill a hole of the diameter of the rivet which is to be used to connect the elements. Place the rivet in the hole.
Install all the pieces of equipment in the riveting machine.
Install an appropriate head.
Connect the riveting machine to the pneumatic system.
Place the head of the riveter on the protruding stem of the rivet so as it touches the rivet (VII).
Push the trigger; after riveting and cutting the remaining part of the rivet, the device is ready for the next riveting.
Once the job has been concluded, the pneumatic system must be dismantled and maintenance operations of the device must
be executed.
MAINTENANCE
Never use petrol, solvents or other infl ammable liquids to clean the device. The vapours may ignite and cause an explosion of the
tool and, in consequence, serious injuries.
Solvents used to clean the grip and the body of the machine may cause softening of the sealing. Dry the tool thoroughly before
commencement of the work.
If any irregularities in the operation of the machine are detected, the tool must be immediately disconnected from the pneumatic
system.
All the elements of the pneumatic system must be protected from dirt. Dirt which gets into the pneumatic system may damage the
tool and other elements of the pneumatic system.
Maintenance of the machine before each use
Disconnect the machine from the pneumatic system.
Before each use, put a small quantity of a maintenance liquid (e.g. WD-40) into the air inlet.
Connect the tool to the pneumatic system and turn it on for about 30 seconds. It will permit to spread the maintenance liquid inside
the machine and clean it.
Disconnect the machine from the pneumatic system again.
O R I G I N A L I N S T R U C T I O N
11