Technical Data - YATO YT-3617 Manual Del Usuario

SPECIFICATION OF THE DEVICE
The pneumatic riveter is a device which is powered with a stream of compressed air of appropriate pressure. It is possible to
connect elements using breakable steel, stainless steel and aluminium rivets. The device is more effi cient and comfortable than a
hand riveter. Correct, reliable and safe functioning of the machine depends on proper operation, and therefore:
Before operation of the machine can commence, read the whole manual and keep it.
The supplier of the device cannot be held responsible for any damage and injuries resulting from using of the tool contrary to its
purpose, not observing safety regulations and the provisions of the present manual. If the device is used contrary to its purpose,
the user looses all guarantee rights due to a breach of contract.
EQUIPMENT
The riveter is equipped with a connector which makes it possible to connect it to a pneumatic system. The equipment also includes
additional heads for rivets of different diameters and wrenches which permit their exchange.

TECHNICAL DATA

Parameter
Catalogue number
Weight
Diameter of the air connector (PT)
Internal diameter of the air supply pipe
Diameter of the rivets
CRUShing pressure
Maximum stroke of the piston
Maximum operating pressure
Recommended operating pressure
Required fl ow of the air (at 6.2 bar)
Acoustic pressure (EN ISO 15744:2008)
Acoustic power (EN ISO 15744:2008)
Vibrations (EN 28662-1:1992)
GENERAL SAFETY CONDITIONS
WARNING! During operation of a pneumatic tool, it is recommended to always observe the basic safety regulations including
those mentioned below, in order to diminish the risk of fi re, electric shock and injury.
Before operation of the tool can be commenced, the whole manual must be read and kept.
ATTENTION! Read all the instructions mentioned below. If they are not observed, there is a risk of electric shock, fi re or injury.
The notion of „pneumatic tool" that is used in the instructions refers to all tools that are powered with a stream of compressed air
at appropriate pressure.
OBSERVE THE FOLLOWING INSTRUCTIONS
Place of work
The place of work must be well lit and kept clean. Disorder and weak light may be causes of accidents. Do not use pneumatic tools
where there is a risk of explosion, in an atmosphere that contains infl ammable liquids, gases, or fumes. Prevent access of children
and unauthorized persons to the place of work. Loss of concentration may cause loss of control of the tool.
Safety
The connector of the pneumatic tool must fi t the socket of the air supply duct. Do not modify the connector or the power supply
socket. All ducts, connectors and sockets must be clean, undamaged, in good technical state and suitable to be used with
pneumatic tools. Pneumatic tools are not insulated from contact with electric energy sources, and therefore any contact with
grounded surfaces must be avoided (pipes, heaters and refrigerators). Grounding of the body increases the risk of electric shock.
Do not expose pneumatic tools to atmospheric precipitation or humidity. Water and humidity inside the tool increases the risk of
damage and injury. Do not overload the air supply duct. Do not use the duct to carry, connect or disconnect the connector from
the compressed air tank. Avoid contact of the power supply cord with heat sources, oils, sharp edges or mobile elements. Do
not power the pneumatic tool with oxygen, infl ammable or toxic gases. Use only fi ltered and "lubricated" compressed air whose
O R I
All manuals and user guides at all-guides.com
Measurement Unit
[kg]
["]
["]
[mm]
[kg] / [N]
[mm]
[MPa]
[MPa]
[l/min]
[dB(A)]
[dB(A)]
[m/s ]
2
G I N A L
GB
YT-3617
1,5
1/4
3/8
2,4; 3,2; 4,0; 4,8
850 / 8335
14
0,70
0,62
0,85
77,8 ± 3,0
88,8 ± 3,0
0,4 ± 1,5
I N S T R U
Value
YT-3618
2,0
1/4
3/8
2,4; 3,2; 4,0; 4,8; 6,4
1389 / 13 620
19
0,70
0,62
0,99
81,2 ± 3,0
92,2 ± 3,0
0,4 ± 1,5
C T I O N
9