Operating Instructions; Placement And Testing; Tool Change; Tuning Operations - stayer VAC2050C Manual De Instrucciones

4. Operating instructions

4.1 Placement and testing

Initial operation
Observe correct mains voltage: The voltage of the power
source must agree with the voltage specified on the
nameplate of the machine.
Antistatic chain (Fig 14)
Always connect the chain of static discharge (fig.14) to
the bottom of the vacuum cleaner. This will eliminate the
possibility to 100% unpleasant electric shock (cramps)
due to accumulation of static electricity when aspirated
into carpets, rugs and the like.
Switching On and Off
To start the suction cleaner, place operation mode switch
4 ON (-).
To disconnect the vacuum cleaner, place operation mode
switch 4 OFF (O).
Operation with remote automatic Switching
Place switch 4 to the operation symbol with remote
automatic connection (=).
The vacuum cleaner automatically starts operating after
4 seconds after the electrical tool has been switched on.
To terminate the vacuum cleaner's work, switch off
the electrical tool. The vacuum cleaner will disconnect
automatically after approx. 4 seconds. Once turned off,
place switch (o).

4.2 Tool change

Replace a damaged filter immediately.
Insert new or cleaned folded filter and ensure firm seating.

4.3 Tuning operations

Wet Vacuuming
Danger of explosion and fire! Do not vacuum
inflammable or explosive fluids; for example,
benzene, oil, alcohol, solvents. Do not vacuum
hot or burning dust. Do not operate the
machine in rooms where the danger of an explosion
exists.
- Open the fasteners 10 at both sides, raise and remove
the upper part 3 of the vacuum cleaner.
- Before vacuum cleaning liquids, the HEPA dust filter 12
must be removed.
- Empty and clean the suction tank 9 before vacuuming
liquids.
- Before opening and emptying must indispensably
removed the plug in the socket.
- Position collecting bag 11 correctly so that vacuum
cleaner may operate correctly.
- Place the upper part 3 of the vacuum cleaner once the
collecting bag has been positioned, and close using
the clips 10 at both sides.
ENGLISH
13
Dry vacuum cleaning
1. Open fasteners 10 at both sides, raise and remove the
upper part of the vacuum cleaner.
2. Confirm that the fluted filter 12 and the collecting bag
11 are positioned correctly.
3. Place the upper part 3 of the vacuum cleaner, close
using the clips 10 at both sides.
For dry and wet operation always the filter 12
and bag 11 must be positioned correctly.

4.4. General instructions for use

In the case of inadequate vacuuming performance, check
the following:
– Is the vacuum top 3 attached properly?
– Are the extension wands connected firmly?
– Is the container full?
– Is fluted filter 12 saturated with dust?
– Is bag 11 positioned correctly?
The 2-position brush 18 has a pedal for its use for hard
floors (with the brush outwards for better cleaning) and
carpets (with the brush inwards for more efficacious

cleaning).

The round brush 19 is used on narrow and hard surfaces,
e.g. shelves, tables, etc.
The flat nozzle 20 is used in narrow spaces such as
corners, furniture, etc.

5. Maintenance and service instructions

5.1 Cleaning
Before any work on the machine itself, pull the
mains plug.
Always keep the machine clean.
Use compressed air or a damp cloth to keep clean the
vacuum cleaner.
Container
Wipe out the container 9 from time to time with a
commercially available, non-scouring cleaning agent and
allow to dry.

5.2 Repair service

Our after-sales service responds to your questions
conceming maintenance and repair ofyour product as well
as spare parts. Exploded views and information on spare
parts can also be found under: info@grupostayer.com
Our customer consultants answer your
conceming best buy, application
productsand accessories.
13
questions
and adjustment of