Black and Decker PRO Serie Manual De Instrucciones página 12

12 • ENGLISH
making any adjustments, changing accessories,
or storing power tools. Such preventive safety measures
reduce the risk of starting the power tool accidentally.
d. Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the power
tool or these instructions to operate the power
tool. Power tools are dangerous in the hands
of untrained users.
e. Maintain power tools. Check for misalignment
or binding of moving parts, breakage of parts and
any other condition that may affect the power
tools operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
f. Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
5. Service
a. Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power
tool is maintained.
6. Electrical safety
Your tool is double insulated; therefore no earth
wire is required. Always check that the main
voltage corresponds to the voltage on the rating
plate.
Warning! If the power cord is damaged, it must
be replaced by the manufacturer, authorized
Black & Decker Service Center or an equally
qualified person in order to avoid damage or
injury. If the power cord is replaced by an equally
qualified person, but not authorized by Black &
Decker, the warranty will not be valid.
7. Labels on tool
The label on your tool may include the following symbols:
Hz ....... Hertz
Read
Instructions
W ........ Watts
Manual
min ..... minutes
Use Eye
Protection
..... Alternating
Current
Use Ear
Protection
..... Direct
Current
V ........ Volts
n ....... No-Load
0
Speed
A ........ Amperes
FEATURES (FIG. A)
1. Lock-on button
2. Variable speed on/off switch
3. Blade storage compartment cover
4. Shoe plate locking lever
All manuals and user guides at all-guides.com
5. Shoe plate
6. Blade support roller
7. Tool-free blade clamp
Additional features (FIG. B)
Additional features may be applicable depending upon the
product purchased. The additional features applicable to
the catalogue number purchased are shown in FIG. A.
f Hold the tool by the insulated gripping surfaces
f Use clamps or another practical way to secure
f Keep hands away from cutting area. Never reach
f Keep blades sharp. Dull or damaged blades may
f When cutting pipe or conduit, make sure that they
f Do not touch the workpiece or the blade
f Be aware of hidden hazards, before cutting into
f The blade will continue to move after releasing
...... Class II
Construction
.... Earthing
Terminal
.... Safety Alert
Symbol
.../min.. Revolutions
or Recipro-
from cutting applications may endanger the health of the
cation per
minute
operator and possible bystanders. Wear a dust mask
specifically designed for protection against dust and fumes
and ensure that persons within or entering the work area
are also protected.
f This tool is not intended for use by persons (including
ADDITIONAL JIGSAWS
SAFETY WARNING
Warning! Additional safety warnings for jigsaws.
when performing an operation where the cutting
tool may contact hidden wiring or its own cord.
Contact with a "live" wire will make exposed metal
parts of the tool "live" and shock the operator.
and support the workpiece to a stable platform.
Holding the work by hand or against your body leaves
it unstable and may lead to loss of control.
underneath the work piece any reason. Do not insert
fingers or thumb into the vicinity of the reciprocating
blade and blade clamp. Do not stabilize the saw by
gripping the shoe.
cause the saw to swerve or stall under pressure.
Always use the appropriate type of saw blade for the
workpiece material and type of cut.
are free from water, electrical wiring, etc.
immediately after operating the tool. They can
become very hot.
walls, floors or ceiling, check for the location of
wiring and pipes.
the switch. Always switch the tool off and wait for the
saw blade to come to a complete standstill before
putting the tool down.
Warning! Contact with, or inhalation of dusts arising
children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge,
unless they have been given supervision or instruction