Topping Up The Chain Oil Tank; Cleaning; Chain Catcher; Machine And Bar Lubrication Holes - ST MP 500 Li 48 Manual De Instrucciones

Podadora alimentada por batería
Ocultar thumbs Ver también para MP 500 Li 48:
Tabla de contenido

Publicidad

4. connect the battery charger (Fig. 23.C) to a
power outlet with a voltage corresponding
to that indicated on the rating plate;
5. fully charge the battery according
to the instructions in the battery/
battery charger booklet.
NOTE The battery is equipped with a guard
that inhibits recharging if the environmental
temperature is not between 0 and +45 °C.
NOTE The battery can be recharged at any
time, even partially, with no risk of damaging it.
7.2.3 Refitting the battery on the machine
When recharging is completed:
1. Remove the battery (Fig. 24.A) from its
housing in the battery charger (Fig. 24.B)
(avoiding to keep it under charge for a
long time after recharging is completed);
2. disconnect the battery charger
(Fig. 24.C) from the mains;
3. insert the battery in its housing fitted on the
machine (Fig. 17.B) or in one compartment of
the battery backpack (Fig. 12) (if provided).;
4. push down the battery all the way until
you hear a " click" that locks it in place
and guarantees the electrical contact;

7.3 TOPPING UP THE CHAIN OIL TANK

IMPORTANT Only use chainsaw
oil or adhesive oil for chainsaws. Do
not use oil containing impurities so as
not to block the oil filter and to prevent
irreparable damage to the oil pump.
It is essential that you use good quality oil
to lubricate the cutting parts effectively.
Used or poor quality oil does not
guarantee good lubrication and reduces
the working life of the chain and bar.
IMPORTANT Never run the chain
without sufficient oil, this could damage the
Pruner device and compromise safety.
If the oil level is low, top up as follows:
1. Unscrew and remove the cap
(Fig. 25.A) from the oil tank.
2. Pour oil in the tank and monitor the
level on the indicator (Fig. 25.B).
3. Make sure no impurities penetrate
the oil tank when filling.
4. Screw on the oil cap and tighten it.

7.4 CLEANING

7.4.1 Cleaning the machine and the motor
After every work session, clean the machine
thoroughly to remove all dust and debris.
• To reduce fire hazards, keep the machine
and, in particular, the motor free of
leaves, branches or excessive grease.
• Always clean the machine after use with a
damp cloth dipped in neutral detergent.
• Remove all traces of humidity using
a soft damp cloth. Humidity can
generate risks of electric shocks.
• Do not use aggressive detergents or solvents
to clean the plastic parts or hand grips.
• Do not spray water onto the motor
and electrical components and
prevent them from getting wet.
• To avoid overheating and damage to the
motor or the battery, always keep the
cooling air vents clean and free of debris.
7.4.2 Cleaning the chain
Remove any traces of sawdust or oil deposits
from the chain every time it is used.
If there is excessive dirt or resin build-up,
disassemble the chain and place it in a container
with a specific cleanser for a few hours. Then
rinse it with clean water and treat it with a suitable
anticorrosive spray, before reassembling on the
machine.

7.5 CHAIN CATCHER

Check the chain catcher conditions before each
use (Fig. 1.I) and repair in the event of damages.
7.6 MACHINE AND BAR
LUBRICATION HOLES
Before daily use, remove the guard (par. 4.2),
disassemble the bar and check that machine
lubrication holes (Fig. 26.A) and guide bar
(Fig. 26.B) are not clogged.

7.7 NUTS AND BOLTS

• Keep all nuts, bolts and screws tight to be sure
the equipment is in safe working condition.
• Check regularly that the handles are fixed firmly.
EN - 13

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Mp 700 li 48

Tabla de contenido