Storage; Electrical Connection; Air Pipe (Extension) And Utensils Connection; Safety Devices Adopted - Senco AC33024 Instrucciones De Empleo

10. STORAGE

EN
• In the instance where the appliance is not to be used for an
extended period of time, it must be stored in a safe place,
with suitable temperature and air humidity values, where it is
protected from dust.
• Before storing the appliance, we recommend draining mois-
ture from the air tank.

11. ELECTRICAL CONNECTION

The machine can be connected to the mains electrical supply
by plugging the power cable into the special socket.
THE POWER SUPPLY NETWORK TO WHICH THE
APPLIANCE IS CONNECTED MUST CONFORM TO THE
LEGISLATION CURRENTLY IN FORCE IN THE
COUNTRY OF USAGE, CONFORM TO THE TECHNICAL
SPECIFICATIONS PROVIDED IN PARAGRAPH 2 AND BE
EQUIPPED WITH A SUITABLE "PLANT EARTHING" SYSTEM.
ALL MATERIALS USED FOR ELECTRICAL CONNECTION MUST
BE SUITED TO THE INTENDED USAGE, LABELLED WITH "CE"
IF SUBJECT TO THE LOW VOLTAGE DIRECTIVE 2006/95/CE
AND CONFORM TO THE REQUIREMENTS AS SPECIFIED IN
THE LEGISLATION CURRENTLY IN FORCE IN THE COUNTRY
OF APPLIANCE USAGE.
DISREGARD FOR THE ABOVE DESCRIBEDWARNINGS MAY
LEAD TO IRREPERABLE DAMAGE TO THE APPLIANCE ELEC-
TRICAL SYSTEM AND SUBSEQUENTLY WARRANTY EXPIRY.
THE MANUFACTURER DECLINES ANY RESPONSIBILITY FOR
FAULTS OR ANOMOLIES WITH APPLIANCE OPERATION
CAUSED BY ELECTRICAL POWER SURGES IN ADDITION TO
TOLERANCES BY THE SUPPLY ENTITY (VOLTAGE ± 10%,
FREQUENCY ± 2%).
WHERE NECESSARY, CONNECT THE APPLIANCE EXCLUSIVE-
LY TO THE ELECTRICAL SUPPLY GENERATOR WITH POWER
GRTEATER THAN THE INSTALLED ELECTRICAL POWER (SEE
PARAGRAPH 30), IN ORDER TO SUPPORT THE POWER-DRA-
WAT START-UP.
12. AIR PIPE (EXTENSION) AND UTENSILS
CONNECTION
1) Connect the utensil to the air pipe (extension).
2) Connect the air pipe (extension) to the appliance air outlet
spigot (rif. 14).
THE MANUFACTURER DECLINES ANY RESPONSIBILI-
TY FOR DAMAGE TO PERSONS, ANIMALS AND
OBJECTS CAUSED BY THE INOBSERVATION OF THE
ABOVE DESCRIBEDWARNINGS.
AIR PIPES (EXTENSION), CONNECTIONS AND UTENSILS
WHICH CONFORM TO THE MANUFACTURER'S INSTRUCTION
MANUALS MUST BE USED.
THE USE OF UNSUITABLE AIR PIPES (EXTENSIONS),
CONNECTIONS AND UTENSILS AND/OR THOSE WHICH DO
NOT COMPLY WITH LEGILATION CURRENTLY IN FORCE IS
STRICTLY FORBIDDEN.

13. SAFETY DEVICES ADOPTED

1) SAFETY VALVE (4): a certified safety valve (set to 10.5
bar), installed to the pneumatic system, under the pressure
switch. It tackles over-pressure in the instance where,
owing to anomalies, the pressure switch does not function.
Safety valve intervention ensures the operator switches off
the appliance and requests the support of maintenance
persons.
2) PRESSURE SWITCH (8): an electro-pneumatic device (set
to a minimum of 7 bar and a maximum of 10 bar) installed
to the pneumatic system. It serves to control the automatic
start-up of the appliance when the operating pressure
comes down to 7 bar and the automatic close-down when
the pressure reaches 10 bar.
3) FIXED COOLING FAN PROTECTIVE NET (17): fixed
protection made of plastic attached using screws fixed
to the twin cylinder pump system base. It serves to stop
accidental contact with the cooling fan when in motion.
4) THERMAL RESTORE (12): thermal protection installed to
the electrical system, which stops the electric motor in the
instance of power overload and/or a short-circuit. Reset
can be carried out by acting on the relative button (A).
5) TANK PRESSURE GAUGE (6): a measuring device installed
to the appliance tank. It displays the compressed air pres-
sure inside the tank.
6) OUTLET PRESSURE GAUGE (7): a measuring device
installed to the appliance pneumatic system above the air
outlet spigot. It displays the outlet pressure, which can be
adjusted using the relative pressure regulator (0÷10 bar)
(13).
ALL SAFETY DEVICES INSTALLED ON THE APPLI-
ANCE MUST BE REGULARLY CHECKED TO ENSURE
THEY ARE FUNCTIONING CORRECTLY.
ANY SAFETY DEVICES WHICH ARE NOT FUNCTIONING COR-
RECTLY OR WHICH ARE DAMAGED MUST BE IMMEDIATELY
REPLACED.
THE HANDLING, EXCLUSION AND/OR REMOVAL OF
SAFETY DEVICES INSTALLED ON THE DEVICE IS STRICTLY
FORBIDDEN.
REPLACING A SAFETY DEVICE OR COMPONENTS OF SAFETY
DEVICES WITH UNORIGINAL REPLACEMENT PARTS IS
STRICTLY FORBIDDEN.
6
14