EURO-PRO Shark INFINITY NV31N Manual Del Usuario página 4

OPERATING INSTRUCTIONS
Using the Vacuum for Above Floor
Cleaning
Your vacuum can be used to dust above
floor areas such as tops of furniture,
upholstery, drapes, etc. When using with
accessories, you must place the carpet-to-
floor selector to the "Bare Floor/Tools"
position.
Crevice Tool
For radiators, crevices, corners,
baseboards and between cushions.
Upholstery/Dusting Brush
The upholstery/dusting brush is two brushes
in one. To use as an upholstery brush, you
must remove the dusting brush attachment.
To remove, just snap the two pieces apart.
(Fig. 7) Use the upholstery brush to remove
dust and pet hair from furniture. Use the
dusting brush to dust furniture, Venetian
blinds, books, lamp shades and shelves.
=
+
Fig. 7
Pet Hair Power Brush
Unique pet design with duel felt
strips to grab and remove
pet hair from furniture.
Bare Floor Brush
The soft natural bristles
will not scratch floors.
Glides easily under
furniture to vacuum
up pet hair.
Note: The bare floor brush can
only be used with the telescopic wand.
Attaching the Accessories
All the accessories can be attached either
to the handle or to the telescopic wand
except for the bare floor brush which can
only be attached to the telescopic wand.
To attach the accessories to the
handle:
1. Press the handle lock release
and pull the handle up to
remove it from the
telescopic wand.
Press
(Fig. 8)
Handle
2. Push the desired
Lock
Release
accessory onto
the end. (Fig. 9)
3. To remove the
accessories, just
pull them out.
Fig. 8
All manuals and user guides at all-guides.com
To attach the accessories to
the telescopic wand:
1. Press the telescopic wand release
button and pull the telescopic wand out
of the vacuum. (Fig. 10)
2. Push the desired accessory onto the
end. (Fig. 11, Fig. 12)
3. To remove the accessories, just pull
them out.
Press
Fig. 11
Fig. 10
Fig. 12
Using the Accessories
1. To avoid tip over, always make sure
that the hose is inserted into the
lower hose holder that is located at
the bottom of the unit, just behind the
dust cup container. (Fig. 13)
Lower
Hose
Holder
Fig. 13
5
2. Turn the quick release cord holder 180°
to either side to release the power cord.
3. Plug the power cord into the electrical
outlet.
4. When using the attachments, the
vacuum must be in the upright position.
Fig. 9
5. Ensure that brush roll is locked by
pressing the carpet-to-floor selector to
the "Bare Floor/Tools" position. (Fig. 14)
CAUTION:
Do NOT pull the vacuum
cleaner around the room by the hose as it
could tip over and cause damage. When
using the attachments, do NOT over
extend the hose length when reaching.
Trying to reach beyond the hose reach
could cause the vacuum to tip over.
WARNING:
Avoid tipping the vacuum or
setting it on furniture, fringed area rugs or
carpeted stairs while you are using the
hose with the attachments. When the
vacuum is turned on, the brush roll will
continue to rotate until you put the carpet-
to-floor selector to the "Bare Floor/Tools"
position. Avoid leaving the vacuum in one
place for an extended period of time,
particularly on thick carpet.
Note:
When lifting your vacuum from the
carry handle, be careful not to press the
dust cup release button because you will
release the dust cup assembly.
Vacuuming Floors & Carpets
The upright vacuum can be used to vacuum
all types of carpeting and bare floors.
The carpet-to-floor selector should only be
adjusted while the vacuum cleaner is turned
on and is in the upright position.
1. Turn the quick release cord holder
180° to either side to release the
power cord.
2. Plug the power cord into
the electrical outlet.
3. Depress on the handle
release pedal to
release the handle.
(Fig. 15)
OPERATING INSTRUCTIONS
4. When vacuuming carpets, set the
carpet-to-floor selector to the "Carpet"
position to engage the brush roll.
(Fig. 16)
5. When vacuuming bare floors, set the
carpet-to-floor selector to the "Bare
Floor/Tools" position. This will lock the
brush roll and it will not turn. (Fig. 17)
CAUTION:
the carpet-to-floor selector while the
vacuum cleaner is turned off.
Bare Floor / Tools
Fig. 14
Fig. 16
How to Adjust for Carpet Height
WARNING
clothing, hair, fingers and all other parts
of body away from any moving parts
(such as the beater brush). Turn off the
switch and unplug the vacuum before
adjusting the vacuum for the carpet
height.
The front of the power nozzle has a
carpet height adjustment knob that
raises and lowers the motorized power
head to match the type of carpet.
(Fig. 18) With the vacuum NOT
connected to the electrical outlet, set the
adjustment to the lowest setting for
maximum cleaning. If the vacuum is too
difficult to push, move the knob to the
next highest setting until the vacuum is
comfortable to push. The brush roll must
reach the carpet for the most effective
cleaning.
Carpet Height
Adjustment Knob
Fig. 15
6
Do not change the setting of
Carpet
Bare Floor /
Position
Tools
Fig. 17
: To avoid injury, keep loose
Fig. 18