Maintenance Instructions - EURO-PRO Shark INFINITY NV31N Manual Del Usuario

MAINTENANCE INSTRUCTIONS

IMPORTANT NOTE:
See the
manufacturer's recommendations when
vacuuming delicate or hand woven
carpets. They may suggest vacuuming
your carpet with the power nozzle on a
low height with the brush roll "Off. If this
is the case, set the carpet height
adjustor to the lowest setting and place
the carpet-to-floor selector to the "Bare
Floor/Tools" position.
WARNING:
Always empty the dust cup
after each use and during prolonged
usage. Never over fill the dust cup
beyond the "MAX" fill line - remove dirt
and clean the debris screen each time
the dust cup is emptied or during
prolonged usage or risk motor damage.
Empty the cyclonic chamber every three
months depending on the amount of
usage. Never let the dust in the cyclonic
chamber surpass the "MAX" fill line.
Using the Pet Hair Power Brush
The pet hair power brush may be used
with the telescopic wand or with the
handle.
To use with the handle:
1. Remove the handle from the unit and
push in the power brush.
2. To remove the power brush from the
handle, pull and twist.
To use with the telescopic wand:
1. Press the telescopic wand release
button and pull the telescopic wand
out of the vacuum.
2. Push the power brush onto the end.
3. To remove the power brush, pull and
twist.
The efficiency of your power brush
depends on the bristle brush rotating at
high speed. Strong air suction is needed
to accomplish this. In order to ensure
that maximum air suction is maintained,
please read the following instructions:
1. Empty the Dust Cup prior to reaching
the "MAX" fill line.
2. Ensure that the rotating bristles on
the power brush is kept free of hair
and string.
3. Inspect the turbine regularly to
ensure that the air passage is free of
dirt and debris.
All manuals and user guides at all-guides.com
Cleaning Pet Hair Power Brush
Locking Latch
Tilt
Upwards
Fig. 19
Turbine
1. Slide locking latch forward then tilt the
top housing of the brush upwards.
The top housing is hinged and will tilt
up approximately 45° only. (Fig. 19)
2. Inspect turbine wheel and air passage
for debris and/or blockage. Remove
debris if present.
3. Inspect the rotating bristle brush for
build-up hair or string. If present,
remove by carefully cutting with
scissors. Avoid damaging or cutting
the bristles or the belt.
4. Once clean, close the top cover of the
power brush and slide the locking
latch toward the rear of the brush to
lock.
Removing the Dust Cup Assembly
CAUTION:
Always unplug the unit from
the electrical outlet before removing and
emptying the dust cup. Failure to do so,
may result in electric shock or personal
injury.
To ensure that your vacuum continues to
clean thoroughly, the dust cup should be
emptied after each use and/or each time
it reaches the "MAX" fill line.
1. To remove the dust cup assembly,
press the dust cup release button
and remove the dust cup assembly.
(Fig. 20)
PRESS
Fig. 20
7
MAINTENANCE INSTRUCTIONS
WARNING
: Do NOT push the cyclonic
chamber bottom door release button
while the cyclonic chamber is still
attached to the dust cup.
2. To empty the dust cup, hold the dust
cup assembly over a garbage
container and press on the dust cup
bottom door release button.
(Fig. 21, Fig. 22)
Press
Fig. 22
Fig. 21
Separating the Dust Cup from the
Cyclonic Chamber
1. Remove the dust cup assembly.
2. While holding the dust cup assembly,
twist the carrying handle counter
clockwise to separate the cyclonic
chamber from the dust cup.
(Fig. 23, Fig. 24)
Fig. 23
Fig. 24
Cleaning the Dust Cup & Debris
Screen
To remove the debris screen:
1. Hold the dust cup in one hand and
with the other hold the debris
screen. (Fig. 25)
2. Twist the debris screen counter
clockwise to unlock and remove
from the dust cup. (Fig. 26)
Hold
From the
bottom
Fig. 25
Debris
Screen
Fig. 26
3. Take out the debris screen and rinse
it in lukewarm water by just running
it under the tap to remove any dust
that is adhering
to the screen.
(Fig. 27) Do
NOT place in
dishwasher. Let it
air dry completely
(24 hours) before
reinstalling into Fig. 27
the vacuum.
4. The dust cup can be washed in
lukewarm water. Do not use strong
detergents. (Fig. 28)
5. Make sure that the
dust cup and the debris
screen are completely
dry before re-assembling.
6. To replace the debris
screen, insert the debris
screen back into the dust
cup. Fit the debris screen
back into position and turn
Fig. 28
clockwise to lock it into
position.
8
Hold &
Twist