Asko W600 Guía De Uso Y Cuidado página 14

The Delayed Start Menu
This menu lets you set a delayed start from 1 to 12
hours. This means you can set the washer to start at
the most convenient time for you, such as an hour before
you arrive home from work. This feature is also useful
in areas where utility companies offer discount rates
during certain hours.
Se le c t time
for delayed start
< - + >
P1
M e n u
1. Use the Arrow buttons to increase or decrease the
delay time. (The numbers indicate hours.)
2. When the number of hours you want to delay starting
the machine displays, press ENTER. The LED will
display the delay start time.
Press MENU to advance to the next menu.
The Options Menu
This menu lets you set several options. Only the options
available with the wash program you selected will display.
(See ”The Program Menu” table on page 11.)
Se le c t
rpm
options
1600
Pre-soak
< O ff
P1
0
M e n u
1. On this menu, you press ENTER to advance through
the options, rather than pressing MENU.
2. Press an Arrow button to toggle between Off and On.
3. When your preference displays, press ENTER. The
LED will display the new options. Continue to press
ENTER until the LED displays your new program.
RESTORING A PRESET
PROGRAM
To restore a preset program to its original settings,
simply press the button for the preset program you want
to restore and hold it down while your press ENTER.
The program will revert to its original settings.
NOTE: If you change the P3 program then decide to
restore its original settings, after pressing P3
and ENTER, you must go into the Options
menu (see page 14) and turn off Short Spin.
Page 14
All manuals and user guides at all-guides.com
0
E n t e r
>
E n t e r
CHANGING THE LANGUAGE
ON THE LED WINDOW
There are eleven languages available for the LED
window:
¨
English
¨
French
¨
Spanish
¨
Portuguese
¨
Italian
¨
German
To change the language, follow the steps below:
1. Turn the machine off then on again.
2. Press ENTER five times in succession then press
P1 five times. (This must be done within 15 seconds.)
3. When the Language menu displays, press an Arrow
button to advance through the menu to the desired
language.
4. Once the correct language displays, press ENTER
to program the LED window to display the language
you selected.
CHANGING THE TEMPERATURE
READOUT ON THE LED WINDOW
FROM CELSIUS TO FAHRENHEIT
You can change the temperature readout on the LED
window from Celsius to Fahrenheit and vice versa. To
do this follow the steps below:
1. Turn the machine off then on again.
2. Press ENTER five times in succession then press
P2 five times. (This must be done within 15 seconds.)
3. When the Temperature menu displays, press an
Arrow button to toggle between Fahrenheit and
Celsius.
4. When your preference displays, press ENTER to
program the LED window to display the temperature
reading you selected.
CHILD-SAFE START (W640/W660)
As a safety measure, you can program the W640 and
W660 not to start unless the START button is held down
for three seconds. To do this, follow the steps below:
1. Turn the machine off then on.
2. Press ENTER five times, then press P3 five times.
(This must be done within 15 seconds.)
3. “Delayed start” displays with “0” flashing in the lower
right corner. Press the right Arrow button to toggle
the display to “3.”
Child-Safe Menu Button
Please note that when you set the child-safe Start button,
the Menu button is automatically programmed to delay
for three seconds before it becomes active. This prevents
a child from accidentally changing the program settings.
When you want to change a program, press the Menu
button for three seconds to activate the menus. The
Menu button will work normally (without the 3-second
delay) until you have completed your changes. If it is not
pressed for two minutes, it will automatically revert back
to the child-safe mode.
¨
Swedish
¨
Danish
¨
Norwegian
¨
Netherlands
¨
Finnish