Comunello Automation QUAD-24V-HP Instrucciones De Uso Y De Instalacion página 22

• Make sure you have enabled the extended Menu 1 (as shown by the alternate flashing 1 0 1 0 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L4;
• Press the SET key;
• LED L4 becomes steady on and programming will be completed.
Repeat the procedure if you wish to restore the previous configuration.
8.2.5. LED L5 - DS2 STOP IN CLOSE:
The control unit allows the operation of input DS2 to be modified. If you want DS2 to trip also during closing (stopping of the gate leaf, then
once the passage is free, the gate resumes the closing manoeuvre) proceed as follows:
• Make sure you have enabled the extended Menu 1 (as shown by the alternate flashing 1 0 1 0 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L5;
• Press the SET key;
• LED L5 becomes steady on and programming will be completed.
Repeat the procedure if you wish to restore the previous configuration.
8.2.6. LED L6 - DS1 PARTIAL INVERSION:
The control unit allows the operation of input DS1 to be modified. If, during a closing manoeuvre, you want DS1 to perform a partial reversal
(short reversal) of the gate leaf instead of a total reversal, proceed as follows:
• Make sure you have enabled the extended Menu 1 (as shown by the alternate flashing 1 0 1 0 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L6;
• Press the SET key;
• LED L6 becomes steady on and programming will be completed
Repeat the procedure if you wish to restore the previous configuration.
8.2.7. LED L7 - BLOCK / 8K2:
The control unit allows the connection of an N.C. Emergency Stop pushbutton (CN2 input no. 8). However, to switch this input to an 8.2
KOhm resistive input proceed as follows:
• Make sure you have enabled the extended Menu 1 (as shown by the alternate flashing 1 0 1 0 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L7;
• Press the SET key;
• LED L7 becomes steady on and programming will be completed.
From this moment on, the connection of a resistive edge to the control unit in the relative input will result in the colour change (from red to
green) of the STOP / 8K2 led.
A change in the input value causes a partial inversion and the subsequent block of the control unit in any phase of the leaf stroke.
Repeat the procedure if you wish to restore the previous configuration.
8.3 EXTENDED MENU 2
The control unit is factory set to allow direct selection exclusively of the main menu functions.
If you wish to enable the functions described in Extended Menu 2, proceed as follows:
• Select blinking LEV LED and press SET twice;
• Premere 2 volte SET;
• The LED will start blinking (alternate flashing of LED LEV
L1 BRAKE
L2 STEP BY STEP 1
L3 ALWAYS CLOSE
L4 FOLLOW ME
L5 PEDESTRIAN TIME
L6 2°CH MONOSTABLE
L7 DISTANCE PROGRAM.
LEV MENÙ
This will allow 30 seconds for the selection of Extended Menu 2 functions using the SEL and SET buttons. After a further 30 seconds, the
control unit returns to the main menu.
8.3.1 LED L1 - BRAKE:
The control unit is factory set with the electronic brake function disabled. This will allow 30 seconds for the selection of Extended Menu 2
functions using the SEL and SET buttons. After a further 30 seconds, the control unit returns to the main menu ed as follows:
• Make sure you have enabled the extended Menu 1 (as shown by the alternate flashing 1 1 0 1 1 0 1 1 0 of LEV LED);
• By the key SELECT, position yourself on the blinking LED L1;
• Press the SET key;
• LED L1 becomes steady on and programming will be completed.
COMUNELLO ®Copyright 2021 - All rights reserved
50
ON
ON
ON
ON
ON
ON
ON
);
OFF
OFF
OFF
OFF
OFF
OFF
OFF
2 FLASHES