Hitachi P 20SA2 Instrucciones De Montaje página 7

Planer Safety Rules
Wait for the cutter to stop before setting the tool
down.
An exposed cutter may engage the surface leading
to possible loss of control and serious injury.
PRECAUTIONS ON USING PLANER
Do not use the Planer with the blades facing upward
(as stationary type planer).
SPECIFICATIONS
Voltage (by areas)*
Power Input
Cutting Width
Max. Cutting Depth
Weight (without cord and guide)
No-Load Speed
* Be sure to check the nameplate on product as it is subject to change by areas.
STANDARD ACCESSORIES
1. Box Wrench (for securing cutter blade) ............. 1
2. Set Gauge (for adjusting cutter height) .............. 1
3. Guide (with set screw) ........................................... 1
4. Depth Guide .............................................................. 1
5. Blade Sharpening Ass'y
(for Resharpenable Blade Type) .......................... 1
Standard accessories are subject to change without notice.
OPTIONAL ACCESSORIES (sold separately)
1. Dust collection adapter (Code no. 317279)
Optional accessories are subject to change without notice.
APPLICATIONS
Planing various wooden planks and panels.
(See Fig. 1-4)
PRIOR TO OPERATION
1. Power source
Ensure that the power source to be utilized conforms
to the power requirements specified on the product
nameplate.
2. Power switch
Ensure that the power switch is in the OFF position.
If the plug is connected to a receptacle while the
power switch is in the ON position, the power tool
will start operating immediately, which could cause
a serious accident.
3. Extension cord
When the work area is removed from the power
source, use an extension cord of sufficient thickness
and rated capacity. The extension cord should be
kept as short as practicable.
4. Prepare a stable wooden workbench suitable for
planing operation. As a poorly balanced workbench
All manuals and user guides at all-guides.com
(110V, 115V, 120V, 127V, 220V, 230V, 240V)
PLANING PROCEDURES
1. Adjusting the cutter depth:
(1) Turn the knob in the direction indicated by the
(2) The cutting depth can be adjusted within a range
2. Surface cutting:
3. Beginning and ending the cutting operation:
4. Precaution after finishing the planing operation:
Use dust collection adapter if need to reduce dust
related hazards.
(1) Unscrew the Chip guide (Item no. 17 show in
assembly drawing) on housing.
(2) Mount dust collection adapter on housing with
screws instead of the Chip guide.
Dust collection adapter (Code no. 317279)
(3) Connect the dust extraction and collection
facilities with the tube of dust collection adapter
firmly.
720W*
82mm
3mm
3.0kg
14000/min
creates a hazard, ensure it is securely positioned
on firm, level ground.
arrow in Fig. 5 (clockwise), until the triangular mark
is aligned with the desired cutting depth on the
scale. The scale unit is graduated in millimeters.
of 0-3mm.
Rough cutting should be accomplished at large
cutting depths and at a suitable speed so that
shavings are smoothly ejected from the machine.
To ensure a smoothly finished surface, finish cutting
should be accomplished at small cutting depths and
at low feeding speed.
As shown in Fig. 6, place the front base of the
planer on the material and support the planer
horizontally. Turn ON the power switch, and slowly
operate the planer toward the leading edge of the
material. Firmly depress the front half of the planer
at the first stage of cutting, as shown in Fig. 7,
depress the rear half of the planer at the end of
the cutting operation. The planer must always be
kept flat throughout the entire cutting operation.
When the planer is suspended with one hand after
finishing the planing operation, ensure that the
cutting blades (base) of the planer do not contact
or come too near your body. Failure to do so could
result in serious injury.
English
6